Do Trailer Leaf Springs Have to Face a Certain Direction

Question

Question:

I have a trailer with brakes. Does it matter if the spring leaf clip is forward or aft of the Axel? I suspect the clip is there only for spring assembly, stacking of the leafs, but wonder if it might also have something to contribute when braking and torsion is added to the spring.

asked by: Alan T

0

Expert Reply:

The clip that goes around 3 of the leaves of the 5-Leaf Spring part # e34SR that you referenced can go either in front of the axle or behind it. Either way would be perfectly fine.

I attached an FAQ on trailer suspension for you to check out as well.

expert reply by: Jameson C

0

Stan O.

11/10/2021

Can you purchase the clips for leaf springs and install on both ends? Does the installed direction of the spring clip really matter? What is the purpose of the spring clip?

Reply

Les D.

11/12/2021

Leaf spring clips are not sold. If the are damaged, the entire leaf spring is replaced. Additional clips are not to be installed. Most sources say there is not a front or back, However, one of our suspension suppliers says that the clip side goes to the front, and every trailer I have ever seen has the clip to the front. My wild guess is that this is the beneficial orientation where the leaves are being held as a wheel is entering a pot hole or hitting an obstruction.

Reply

Answer 1

Yes, you can weld on the Dexter DX7.5L A-60 Brake Actuator w Electric Lockout - Bolt On - Disc - 2" Ball - Zinc - 7.5K item #DX56FR you referenced. You will want to make sure you remove the zinc coating and get down to the bare metal. I…

view full answer...

Answer 2

The majority of brake line installations we do in our shop match the first method you have in the photo, labeled "Branch". We also prefer to use rubber hoses as they are easier to work with and there won't be an issue if you…

view full answer...

Answer 3

On a towing setup you are always limited by the lowest rated component as the overall towing capacity since that is the weakest point. When it comes to trailer tires you always want to have them inflated to their max psi when cold. Not only do you…

view full answer...

Answer 4

You need a tire and wheel setup with at least 6,400 lb of capacity since that's how much your boat and trailer weighs together so I would not recommend anything in the 13 inch wheel size as nothing in that size will be rated high enough. The…

view full answer...

Answer 5

The guideline when selecting a winch is to weigh the boat when it is fully loaded and ready to travel with supplies, gas, etc. Then, take the gross weight and divide by 1.5, which will tell you the capacity winch you will need. You will want to…

view full answer...

Answer 6

After you have your hub and bearings on your spindle you will then put on the washer, then the nut, and then the nut retainer (yellow piece) from the Nut Kit #RG05-100. The nut retainer helps to keep the nut from backing off and, ultimately, your…

view full answer...

Answer 7

If you only have the nut and a washer but no cotter pin or retaining type washer on the end then that isn't correct and you want to get a piece to help prevent that nut from backing off. If you have a setup like the Spindle Nut Kit for EZ…

view full answer...

Answer 8

Grease seal width is not nearly as important as inner and out diameter. If the seal you have matches the diameters correctly and the bearings are also correct for the hub and spindle you are totally fine. You do not need to seat the seal beyond…

view full answer...

Answer 9

The P in the tire size part p175/80-13 that you referenced indicates that it is for a passenger vehicle and should not be used on a trailer. For a trailer you want to go with a size that starts with ST which stands for specialty trailer. For an ST…

view full answer...

Answer 10

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13…

view full answer...

Answer 11

If there is a tiny bit of play in suspension components that are designed to move you would be fine. 1/16 of an inch isn't very much, and as long as you torqued everything down to spec you would be good to go. Ideally we just don't…

view full answer...

Answer 12

The locating pin in trailer leaf springs are roughly 1/2", and are a standard size between different brands of springs. To lift your trailer with leaf springs the best way is an over-under kit which moves your axle from above the leaf…

view full answer...

Do Trailer Leaf Springs Have to Face a Certain Direction

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching