TorkLift Camper Rear Tie Downs Compatible With SuperHitch Original on 2003 Ram 3500 Long Bed

Question

Question:

Hi, I have a 2003 Dodge Ram 3500 Longbox Dually Crew Cab with factory hitch and have installed the torklift D3109 camper tie-downs recently, do you know if the if the D1102 superhitch will work with the D3109 tie-downs? Apparently they are not listed as compatible but I have read a few comments saying they work together IF you have the factory hitch. Much appreciate any help. Thanks

asked by: Robert G

0

Expert Reply:

They are not compatible, I verified with TorkLift there are different rear tie-downs for your 2003 Ram 3500 long bed for the factory hitch and the TorkLift SuperHitch Original Trailer Hitch Receiver # TLD1102.

The correct fit for your truck and the SuperHitch Original # TLD1102 are the TorkLift Custom Frame-Mounted Camper Tie-Downs # TLR3503.

expert reply by: Kyle S

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

The 18.5x8.5-8 is actually an old tire size that is not used much anymore. The closest metric size to your existing tire would be 215/60-8. Your wheel most likely has a 5-on 4-1/4 inch bolt pattern (see link), you will want to make sure that the bolt…

view full answer...

Answer 4

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 5

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 6

There is a suggested and common method for 6 function trailer wiring. You will have the following functions: Right Turn, Left Turn, Ground, Tail/marker, Brake, Battery. I have included a help article on trailer wiring that includes a diagram and…

view full answer...

Answer 7

From our experiences the Harbor Freight trailers like yours have a hub bore that requires a cap or Bearing Buddy that measures 2.047 inches like the #BB2047 you referenced. We don't have a standard cap that fits this size so the Bearing Buddy is…

view full answer...

Answer 8

Yes, the Curt hitch part #C77ZV is a fit for the 2023 Toyota Crown Hybrid. I attached a link to the install instructions as well as a link to an installer finder in case you wanted to find someone near you to install the hitch.

view full answer...

Answer 9

The B&W Companion OEM 5th Wheel Trailer Hitch #BWRVK3700 is perfectly compatible with cushioned pin boxes like your MORryde RP072-1621HD, so the clunking you're experiencing isn't related to the two components being incompatible. With…

view full answer...

Answer 10

Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…

view full answer...

Answer 11

It's totally normal for a bit of movement between any fifth wheel hitch and the base rails. The feet on the hitch are typically a bit smaller than the slots they slide into for mounting otherwise you'd have a hard time getting your hitch in…

view full answer...

Answer 12

There are 2 different capacities independent of each other though related. Tongue weight is the downward force or weight on the trailer hitch. So it is pushing down at the back of the vehicle. The gross trailer weight is the weight of whatever it is…

view full answer...