Dust Cover/Cap Solution for Harbor Freight Trailer

Question

Question:

I too lost one of the dust covers for my harbor freight 4/8 trailer, I bought a set of covers that were 1.98. And they would not fit inside the axle housing . Do you carry the correct size?

asked by: Jim K

0

Expert Reply:

From our experiences the Harbor Freight trailers like yours have a hub bore that requires a cap or Bearing Buddy that measures 2.047 inches like the # BB2047 you referenced. We don't have a standard cap that fits this size so the Bearing Buddy is our best option.

expert reply by: Jameson C

0

Answer 1

There is a suggested and common method for 6 function trailer wiring. You will have the following functions: Right Turn, Left Turn, Ground, Tail/marker, Brake, Battery. I have included a help article on trailer wiring that includes a diagram and…

view full answer...

Answer 2

The factory trailer brake controller port on your 2021 Chevrolet Tahoe is located underneath the dash just to the left of the steering wheel. It will be taped to another harness so it may take a bit of looking to find. Keep in mind that if your…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

Yes, the Curt hitch part #C77ZV is a fit for the 2023 Toyota Crown Hybrid. I attached a link to the install instructions as well as a link to an installer finder in case you wanted to find someone near you to install the hitch.

view full answer...

Answer 5

For your AL-KO 7210 braking assembly, you can use the Hydraulic Brake Kit #AKFBBRK-7 as a replacement. These braking assemblies measure 12" x 2", bolts onto a 5 bolt mounting flange, will work with wheel sizes from 14-1/2"…

view full answer...

Answer 6

The downside to buying a "bargain" trailer kit is that customer support, both in terms of helpful information and available replacement parts, can be scarce. The other issue is that products made to sell at a tempting price point may not…

view full answer...

Answer 7

The bearing number alone is not the best indicator for a specific grease or oil seal. Trailers with the same bearing number could have different seals based on the spindle or hub that is being used. Bearing number 30205 is not a bearing that we offer…

view full answer...

Answer 8

I actually called Harbor Freight about your trailer to determine what size dust cap is used on that trailer. I reached a tech and he stated that the dust cap is 52mm or 2.0488 inches. It looks like the best option is #BB2047 or #BB2047SS . However,…

view full answer...

Answer 9

The hub bore diameter of 2.037" - 2.042" is a rather uncommon size but Harbor Freight Trailers generally do use some rather oddball parts in which replacements are hard to find. Although we do not have any standard grease caps that will…

view full answer...

Answer 10

The closest grease caps we have available to the 2.04 inch hub bore diameter you provided are the Bearing Buddies #BB2047. These are designed for 2.047 inch hub bores so they should work great. They will replace the existing grease caps and provide…

view full answer...

Answer 11

I recommend the Dexter Trailer Idler Hub Assembly for 2,000-lb Axles, #8-258BTUC1 with a 5 on 4-1/2 bolt pattern and wheel size of 13" to 15".

view full answer...

Answer 12

The best way to determine the replacement bearing, race and seal parts needed for a trailer is to pull one of the hubs and remove them so their part numbers can be noted. Usually bearings and seals will have part numbers stamped or molded into them,…

view full answer...

Dust Cover/Cap Solution for Harbor Freight Trailer

Product Page this Question was Asked From

Continue Researching