Ground Clearance on a 2020 Hyundai Sonata w/ the Draw-Tite DT74MR Hitch Receiver
Question:
How much ground clearance is there from the installed hitch? Does the receiver opening end past the rear bumper, and if not, how far out does the ball receiver have to extend to clear the rear bumper?
asked by: Chris
Expert Reply:
I just spoke with my rep at Draw-Tite the bottom of the 1 1/4" receiver for the Draw-Tite Sportframe Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4" item # DT74MR sits 5 1/2" off of the ground. I have attached a picture of the hitch installed on a Hyundai Sonata. The receiver extends to the trim but not past the bumper. I recommend using the Curt Class II Drawbar - 5" Rise - 9-5/8" Long item # C45014 to make sure you have enough clearance to get past your Sonata's bumper. If you need a hitch ball, we have a 2" ball item # C40018 and a 1 7/8" ball item # C40001.
Products Referenced in This Question
1-7/8" Hitch Ball - 3/4" Diameter x 1-5/8" Long Shank - Chrome - 2,000 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 1-7/8 Inch Diameter Ball
- 1-9/16 Inch Shank Length
- 3/4 Inch Diameter Shank
- 2000 lbs GTW
- Class I
- Class II
- CURT
more information >
2" Hitch Ball - 3/4" Diameter x 2-1/8" Long Shank - Chrome - 3,500 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 2 Inch Diameter Ball
- 2-1/8 Inch Shank Length
- 3/4 Inch Diameter Shank
- 3500 lbs GTW
- Class I
- Class II
- CURT
more information >
Curt Class II Drawbar - 5" Rise - 9-5/8" Long - 3,500 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 3/4 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Rise - 5 Inch
- Fits 1-1/4 Inch Hitch
- 3500 lbs GTW
- Class II
- CURT
more information >
Product Page this Question was Asked From
Draw-Tite Sportframe Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Trailer Hitch
- Custom Fit Hitch
- Class I
- 200 lbs TW
- 2000 lbs GTW
- 1-1/4 Inch Hitch
- Concealed Cross Tube
- Draw-Tite
more information >
Featured Help Information
Instructions
Continue Researching
- Search Results: trailer jack
- Shop: Brake Controller
- Shop: Bulldog Round, A-Frame Jack - Sidewind - 15" Lift - 5,000 lbs
- Shop: Round A-Frame Trailer Jack - Sidewind - 15-5/8" Travel - 5,000 lbs
- Video: Curt Hitch Ball - Trailer Hitch Ball - C40018 Review
- Video: Draw-Tite Drawbar Review 36065
- Video: Review of Draw-Tite Hitch Ball - Trailer Hitch Ball - 19258
- Video: Draw-Tite Hitch Ball - Trailer Hitch Ball - TR63822 Review
- Video: Draw-Tite 2 Inch Long Shank Hitch Ball Review
- Video: Curt Ball Mounts - Fixed Ball Mount - C45014 Review
- Video: Bulldog Trailer Jack - A-Frame Jack - BD1700100317 Review
- Q&A: My Draw Bar Will Not Fit All the Way Inside My Draw-Tite Hitch 24812 on my Pontiac Vibe
- Q&A: Curt Ball Mount for 1-1/4 inch Hitch with More Rise and Length than C45520
- Q&A: Will Curt Drawbar Clear Bumper On 2004 Chrysler Town And Country
- Q&A: Custom Trailer Hitch Adapter For Chevrolet Malibu from 1-1/4 hitch to 2 Receiver
- Q&A: Distance From Pin Hole to Ball Mount Platform of Curt Ball Mount C45014
- Q&A: Does The Curt Trailer Hitch Receiver # C98DR for 2023 Hyundai Ioniq 5 Reduce Ground Clearance?
- Q&A: Can I Use a 4 Way Vehicle Connector with 7 Way Adapter and the Curt Echo Brake Controller?
- Shop: Draw-Tite Drawbar for 1-1/4" Hitches - 5" Rise - 10" Long - 3,500 lbs
- Shop: 2" Hitch Ball - 3/4" Diameter x 1-9/16" Long Shank - Chrome - 3,500 lbs
- Shop: Curt RockerBall Shock Absorbing 2" Hitch Ball - 3/4" Diameter Shank - Chrome - 3.5K
- Shop: Curt Echo Wireless Brake Controller - 7-Way Plug Mount w/ Bluetooth App - 1 to 2 Axle - Proportional
- Shop: 2" Hitch Ball - 3/4" Diameter x 2-1/8" Long Shank - Chrome - 3,500 lbs
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Search Results: 44649
- Article: Trailer Wiring Diagrams
- Search Results: 68149
- Shop: Trailer Wiring
- Article: How to Measure for Trailer Hitch Drop
- Search Results: 25580