Custom Trailer Hitch Adapter For Chevrolet Malibu from 1-1/4 hitch to 2 Receiver
Question:
Hi- I have a chevrolet malibu 2010 that I just installed a 1.25inch hitch bar on purchased from you. I also bought the 1.25 to 2inch adapter but its too low. I need to adapt from 1.25inch to 2inch and raise a a few inches, but the ones Im seeing dont look like they give enough extension before the rise for my malibu. Can someone help me figure out? Thanks
asked by: Brad F
Helpful Expert Reply:
My recommendation is to have a custom adapter made for the height and length that you need on your 2010 Chevrolet Malibu with the Draw-Tite Trailer Hitch Receiver # 36479. The center of the hitch pin is about 8-1/2" from your rear bumper. Any adapter that goes from a 1-1/4" receiver to a 2" receiver will reduce the weight capacity of the vehicles receiver by 50%. Be sure to verify your vehicle and hitch ratings to determine if you will have enough capacity for what you intend to haul.
The Gen-Y Weld-On 2" Receiver Tube # 325-GH-002 can be welded to the top of the Curt Class II Drawbar # C45015 to give you a hitch adapter similar to what you are looking for. To do this I recommend having it professionally welded and gussets added for additional strength.
Products Referenced in This Question
Gen-Y Weld-On 2" Receiver Tube - 5-1/2" Long - Steel
- Hitch Fabrication Parts
- Receiver Tube
- 5-1/2 Inch Long
- Raw Finish
- Fits 2 Inch Hitch
- Gen-Y Hitch
more information >
Curt Class II Drawbar - 5" Rise - 11-5/8" Long - 3,500 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 3/4 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Rise - 5 Inch
- Fits 1-1/4 Inch Hitch
- 3500 lbs GTW
- Class II
- CURT
more information >
Product Page this Question was Asked From
Hitch Adapter 1-1/4" to 2" Trailer Hitch Receiver (Class II Only)
- Hitch Adapters
- Hitch Expander
- Bike Racks
- Cargo Carriers
- Hitch Mounted Accessories
- 6 Inch Extension
- Fits 1-1/4 Inch Hitch
- 1-1/4 Inch to 2 Inch
- Tow Ready
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Search Results: trailer jack
- Shop: Brake Controller
- Shop: Bulldog Round, A-Frame Jack - Sidewind - 15" Lift - 5,000 lbs
- Shop: Round A-Frame Trailer Jack - Sidewind - 15-5/8" Travel - 5,000 lbs
- Shop: Square A-Frame Jack w/ Footplate - Drop Leg - Sidewind - 28-3/4" Lift - 3,000 lbs
- Video: Draw-Tite 2 Inch Long Shank Hitch Ball Review
- Video: Curt Hitch Ball - Trailer Hitch Ball - C40018 Review
- Video: Draw-Tite Hitch Ball - Trailer Hitch Ball - TR63822 Review
- Video: Curt Ball Mounts - Fixed Ball Mount - C45014 Review
- Video: Bulldog Trailer Jack - A-Frame Jack - BD1700100317 Review
- Video: Curt Ball Mounts - Fixed Ball Mount - C45015 Review
- Video: Review of Draw-Tite Hitch Ball - Trailer Hitch Ball - 19258
- Q&A: Ground Clearance on a 2020 Hyundai Sonata w/ the Draw-Tite DT74MR Hitch Receiver
- Q&A: Will Curt Drawbar Clear Bumper On 2004 Chrysler Town And Country
- Q&A: Distance From Pin Hole to Ball Mount Platform of Curt Ball Mount C45014
- Q&A: Curt Ball Mount for 1-1/4 inch Hitch with More Rise and Length than C45520
- Q&A: Does The Curt Trailer Hitch Receiver # C98DR for 2023 Hyundai Ioniq 5 Reduce Ground Clearance?
- Q&A: My Draw Bar Will Not Fit All the Way Inside My Draw-Tite Hitch 24812 on my Pontiac Vibe
- Q&A: Can I Use a 4 Way Vehicle Connector with 7 Way Adapter and the Curt Echo Brake Controller?
- Shop: 2" Hitch Ball - 3/4" Diameter x 2-1/8" Long Shank - Chrome - 3,500 lbs
- Shop: 2" Hitch Ball - 3/4" Diameter x 2-3/8" Long Shank - Chrome - 3,500 lbs
- Shop: Draw-Tite Drawbar for 1-1/4" Hitches - 5" Rise - 10" Long - 3,500 lbs
- Shop: 2" Hitch Ball - 3/4" Diameter x 2-1/8" Long Shank - Stainless Steel - 3,500 lbs
- Shop: Roof Rack
- Search Results: hitch fabrication parts
- Shop: Trailer Hitch
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Search Results: brake controller
- Article: How to Measure for Trailer Hitch Drop
- Search Results: trailer brake controller
on Hitch Adapters
