Happy Jack Front Tie Downs For 2021 RAM 2500 w/ 6.4' bed, No Board Under Bed

Question

Question:

Do you have one that fits 2021 ram 2500 6.4 bed

asked by: Steve V

0

Expert Reply:

The HappiJac # LC236326-205221 Truck Mounted Camper Tie Downs are a confirmed fit for 2021 RAM 2500 trucks that are unaffected by running boards or rear hitches.

Most customers who use the HappiJac tie down points also use the HappiJac # LC182898 Turnbuckles to connect the camper to the tiedowns.

expert reply by: Les D

0

Answer 1

The Reese Hitch Box Extension you mentioned, part #RP45292 can be cut down to 24 inches long. At that length, it would have a 8000 capacity when used with a weight distribution system. You'd need to use the extension with a Class V hitch with a…

view full answer...

Answer 2

I spoke with my contact at Reese and as long as you are using the Titan Hitch Box Extension for 2-1/2 inch Trailer Hitches, item # RP45292, at the 24 inch extension length, there are no stabilization chains or cables required. Since your trailer is…

view full answer...

Answer 3

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 4

We have run into this quite a few times in the past, and the best option will be replacing the Lance 7-pin connector with a standard 7-way blade connector like the #PK12706. This will give you a standard 7-way connector to plug into the factory 7-way…

view full answer...

Answer 5

Great question, Jeff! When the Rota-Flex first came out it renovated what a pin box could do and be, but at this point in time that technology is a little more dated and the Gen-Y Hitch Shock Absorbing 5th Wheel Pin Box #325-GH-8040 is the "new…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

It sounds like the purpose of getting the air helper spring would be to counteract the 1 inch compression you're getting in your rear suspension caused by the pin weight of your 5th wheel. If that's the case, I believe that the AirLift 5000…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

Yes, anytime you use a hitch extender or reducer like #HR26 you will lose about 1/3 of your hitches overall capacity. However, since you'll be towing a trailer that weighs between 4,500 to 5,000 lbs, the Brophy Hitch Reducer #HR26 will still work…

view full answer...

Answer 10

You can definitely install the HappiJac tie-downs in the front and use Torklift tie-downs for the rear, but you'll have to purchase the whole Happijac kit #LC236326-205221 since we don't currently offer the front separately. For the rear…

view full answer...

Answer 11

The proper extension for your setup would be the one that allows you to have clearance of your hitch mounted accessory and also allows you to still be able to pull the steps down. If the receiver tube sticks out past the camper too far then you will…

view full answer...

Answer 12

The current Torklift tie down part #TLD3101 that you have installed on your 1997 Dodge Ram 3500 only fits if you have the factory hitch. If you go with the SuperHitch part #TLD1100 you would need to change your rear tie down to the part #TLR3503.

view full answer...