Steel Plate Thickness of Draw-Tite 4916 Weld On Service Body Truck Hitch Bracket

Question

Question:

Whats the thickness of the steel on these brackets.. 1/4?

asked by: Rich

0

Expert Reply:

The # 4916 Draw-Tite Service Body Hitch Weld-On bracket is .375 or 3/8 of an inch thick. I've provided a photo with additional dimensions in case you needed them.

expert reply by: Mike L

0

click to enlarge

Answer 1

The mounting plates included with the Curt Class V Universal Weld-On Receiver #15903 you were looking at are slightly different that the 16" Weld-On Bracket Kit #4916 you mentioned. Our warehouse measured the #15903 brackets and they measure…

view full answer...

Answer 2

If the tow vehicle has a 2 inch hitch, a receiver tube like #337RT25836B would not fit into it, as its outer dimension is roughly 2-1/2 inches square. If your tow vehicle has a 2 inch hitch the longest extension we have available for it is 18 inches,…

view full answer...

Answer 3

From the top of the mounting plates to the top of the B&W Heavy-Duty Trailer Hitch Receiver #BWHDRH25124 receiver is a 5-1/4" drop and then from the rearmost bolt hole to the end of the receiver is 10-7/8" (see attached).

view full answer...

Answer 4

I have attached a photo showing what the distance is between the bolt holes and the dimensions of the mounting brackets for the Draw-Tite Ultra Frame Service Body Trailer Hitch Receiver #41990-16 that you can reference. The installation instructions…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 8

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 9

Thanks for reaching out, Adam! The Buyers Products Hitch Plate with 2" Receiver Tube #3371809060A is designed to fit a Ford chassis, and all of the other HD hitches like this from Buyers Products. For your application you need a universal hitch…

view full answer...

Answer 10

I do have an option for you but the Curt Trailer Hitch Receiver part #C15800 is designed for passenger vehicles like the Ram 3500, Chevrolet Silverado 3500, and GMC Sierra 3500 so it will not fit your 2009 Volvo D13. However, what you can use is the…

view full answer...

Answer 11

Yes, the Buyers Products Flatbed/Flatbed Dump Hitch Plate Bumper with Pintle Mount #3371809050 that you referenced does fit the flatbed/dump bed you have on your 2000 C6500. According to Buyers Products this fits your chassis but will require some…

view full answer...

Answer 12

I think the best option we have for you is a universal weld-on hitch plate like one of the following that I have attached for you. We do not really have any direct fit hitch plates for you so I think this will be the best option we can offer. If you…

view full answer...