Drop and Distance of Hitch Receiver on B&W Heavy-Duty Trailer Hitch Receiver

Question

Question:

I have a 2000 Chevy k3500 with flat bed whats the drop down measurements dont wanna have to cut off anything

asked by: Thomas

0

Expert Reply:

From the top of the mounting plates to the top of the B&W Heavy-Duty Trailer Hitch Receiver # BWHDRH25124 receiver is a 5-1/4" drop and then from the rearmost bolt hole to the end of the receiver is 10-7/8" (see attached).

expert reply by: Jon G

0

Hitch Receiver Distance Dimensions on B&W Heavy-Duty Trailer Hitch Receiver
(click to enlarge)

Bolt Hole Hitch Receiver Dimensions on B&W Heavy-Duty Trailer Hitch Receiver
(click to enlarge)

Answer 1

It looks like you're asking about the B&W Heavy-Duty Trailer Hitch Receiver, part #BWHDRH25122, for your 1996 Ford F-150. You didn't say exactly which dimensions you're looking for but I went out to the warehouse and measured the…

view full answer...

Answer 2

The #BWHDRH25122 has 35-5/8 inches between mounting holes like what you see in the picture I attached. Since you need larger than than let me know what vehicle you have and I can see which would be best fit.

view full answer...

Answer 3

According to B&W the side brackets are 6-1/4" tall for their Heavy-Duty Trailer Hitch Receiver #BWHDRH25124.

view full answer...

Answer 4

I just went out to the warehouse and measured the Curt Trailer Hitch Receiver item #C15845. I have attached a couple of diagrams with the dimensions of this hitch on them. From the center of the back bolt to the front of the receiver is 26" The…

view full answer...

Answer 5

The Curt Trailer Hitch Receiver part #C15845 that you referenced is a confirmed fit for a 2016 Ford F-550 cab and chassis with frame rails spaced 34" apart (outside to outside). However, Curt does not test this trailer hitch with dump body…

view full answer...

Answer 6

I was able to get the measurement of the distance from the bottom of the frame to the top of the receiver on the Draw-Tite #41943- which is roughly 8.75". Draw-Tite was not able to provide me with the other measurement you're asking for…

view full answer...

Answer 7

The distance from the top of the receiver to where it would mount on the bottom of the truck is 6" on the #C15845 Curt Trailer Hitch Receiver. The distances between the mounting bolts vary so I am attaching a picture showing the different…

view full answer...

Answer 8

Yes, check out the picture I attached that has the vertical distances from where the hitch mounts to the frame of the vehicle down to the hitch tube. Since you need at least 6 inches this would clear that by 1-3/8 inches.

view full answer...

Answer 9

I spoke with my contact at B and W and he informed me that the center section of the B and W Hitch part #BWHDRH25124 measures 31-13/16 inches long measured from outside of flange to outside of flange.

view full answer...

Answer 10

Yes, as noted in our fit guide the B&W Heavy-Duty Trailer Hitch Receiver #BWHDRH25122 is only a fit for the cab and chassis models with 34 inch frames of 1991 Chevy truck. Assuming you have a standard bumper, the correct trailer hitch for your…

view full answer...

Answer 11

The B&W Heavy-Duty Trailer Hitch Receiver #BWHDRH25122 that will fit your 1986 Chevy K20 will measure 5.438" from the top of the frame brackets to the top of the receiver. If this is looking like it will not be enough to clear the bottom of…

view full answer...

Answer 12

I am unfamiliar with the Barden Bumper and in my research, I could not find any specific information regarding the Barden Bumper. Our trailer hitches are not tested with aftermarket bumpers. We have two bumpers that have been determined to be a fit…

view full answer...

Drop and Distance of Hitch Receiver on B&W Heavy-Duty Trailer Hitch Receiver

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching