Does 4-Way Mounting Bracket BK4F Work with Curt 4-Way Harness C55411

Question

Question:

I am looking at buying the BK4F four pole connector mount with the C55411 wire harness. Will this wire harness connector fit inside the BK4F correctly or are there certain brand connectors that have the right shape that fit in this holder? Thank you!

asked by: Glenn J

0

Expert Reply:

Yes, the 4-way connector of the part # C55411 that you referenced will work well with the 4-way mount part # BK4F that you also mentioned.

expert reply by: Jameson C

0

Answer 1

For your 2010 Ford Fusion we have the Draw Tite hitch part #24865 which is a confirmed fit and would work well for carrying your 1-1/4 inch hitch bike rack. I attached an install video for this hitch for you to check out as well.

view full answer...

Answer 2

Although the T-One Vehicle Wiring Harness you mention obtains its signals from plugging inline with the existing tail light wiring harnesses, the voltage to power the trailer lights needs to be drawn directly from the battery. The reason for this…

view full answer...

Answer 3

Brophy mounting bracket #BK4F is designed to fit a standard 4-Way flat trailer connector so I don't see any reason why it wouldn't work with Hopkins wiring harness #HM43575.

view full answer...

Answer 4

You seem to have found the silver lining in that your 2014 Ford Fusion is well built! Look for a factory harness that goes from the cab of the vehicle through the firewall. You may have to look in some tight places. If you cannot locate a harness,…

view full answer...

Answer 5

Ball mounts like the Curt #C45100 are available in various lengths. This one happens to be 13-inches long, longer than some. Longer ball mounts are needed, for example, in cases of a truck having a slide in camper in the bed, or when using a…

view full answer...

Answer 6

The Thule Helium #TH44VR will accommodate the 2.40 inch width on your Giant Talon tires. Although, the Thule Helium fits a maximum wheel base of 50 inches and a wheel diameter of 26 inches - 29 inches. If you need a hitch for the Thule Helium, I…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 10

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 11

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Does 4-Way Mounting Bracket BK4F Work with Curt 4-Way Harness C55411

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching