Will Draw-Tite Titan Trailer Hitch # 45293 Fit a 2001 Chevy Silverado 2500HD With a 6-1/2ft Bed

Question

Question:

I have a chevy 2001 2500HD extended cab with the 6 1/2 foot bed. Will this hitch fit this truck since it has an extended cab?

asked by: Dave

0

Expert Reply:

The Draw-Tite Class V Trailer Hitch Receiver # DT45517 is a great choice for your 2001 Chevrolet Silverado 2500 HD with 6-1/2 foot bed. This hitch is confirmed to fit your truck and it will accommodate a full size spare tire under the truck. The # DT45517 hitch is confirmed to fit both 2WD and 4WD models with heavy-duty suspension, and there are no fit limitations based on cab length.

This trailer hitch offers a gross trailer weight capacity of 13,000 pounds and tongue weight capacity of 1,300 pounds. When used with weight distribution, these capacities are increased to 17,000 pounds towing and 1,700 tongue weight.

The installation instructions for this hitched are linked to this page for you.

expert reply by: Sarah L

0

Answer 1

For an extension as long as you'd need to have a 2-1/2 inch hitch installed so that you could use the hitch extender part #RP45292 which can be trimmed down to 24 inches. If you were in need of a 2-1/2 inch hitch then you'd need the part…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 4

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...

Answer 5

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Answer 6

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 7

The proper replacement inner assembly member for your UFP 34043 would be indeed be the the Dexter #DX99FR which is compatible with disc brakes. The replacement has an electric lock out and has a 7500K capacity and is intended to work with a 2 inch…

view full answer...

Answer 8

There is a suggested and common method for 6 function trailer wiring. You will have the following functions: Right Turn, Left Turn, Ground, Tail/marker, Brake, Battery. I have included a help article on trailer wiring that includes a diagram and…

view full answer...

Answer 9

Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…

view full answer...

Answer 10

The AL-KO trailer hub part number 8700 that you have is a 3,500 lb trailer hub/drum with a 5 on 4-1/2 inch bolt pattern. Based on that the #AKHD-545-35-EZ-K is the correct fit and would work great.

view full answer...

Answer 11

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 12

From our experiences the Harbor Freight trailers like yours have a hub bore that requires a cap or Bearing Buddy that measures 2.047 inches like the #BB2047 you referenced. We don't have a standard cap that fits this size so the Bearing Buddy is…

view full answer...