Curt Trailer Hitch Receiver - Custom Fit - Class IV - 2"

See what our Experts say about this CURT Trailer Hitch

• Class V Hitch for 2003 GMC Savanah Cutaway
  Buyers Products Class V hitch # 3371801102 fits the cutaway cab and chassis version of the 2003 GMC Savana Van. For the cargo and passenger van version their Class V hitch # 3371801100 is the correct fit. I am not sure which version of the base vehicle you have (nor could Buyer's Products confirm based on it having been made as a school bus) so what you can do to determine which hitch will fit is simply look at the frame under the van. If you refer to the photos of the two hitches you...
  view full answer...
  
• Trailer Hitch Recommendation for 2019 Chevy Express 4500 Cutaway Chassis
  For your 2019 Chevy 4500 Cutaway Chassis we have the Buyers Products part # 3371801102 as a confirmed fit. This is only option we have currently but it has great towing capacities at 12,000 lbs trailer weight and 1,200 lbs tongue weight.
  view full answer...
• Trailer Hitch for a 1976 Chevy C or K Series Short Bed Stepside Pickup
  We have some hitch options that fit your 1976 Chevy C or K series short bed stepside pickup. In this case the stepside bed does not matter. The length does. You can use Curt Class III hitch # 13028 or Class IV hitch # C14082. For # C14082 the frame width will need to be 34 inches (measured outside to outside). Or you can use Draw-Tite hitch # 75034-011 (does not fit models with heavy duty suspension). I have linked instructions for these hitches for you.
  view full answer...
• Recommended Hitch for a 2011 Itasca Suncruiser 35P Motorhome
  Yes, there is and you are in luck because there is a custom fit option. The Curt Trailer Hitch item # C14082 will bolt directly to the frame of your 2011 Itasca Suncruiser 35P. This is a class IV hitch with a 2" receiver. It has a 10,000 lbs towing capacity and a 1,000 lbs maximum tongue weight. The Curt Trailer Hitch item # C14082 fits frames that are 34" wide. It also does require drilling as there are no predrilled holes for a hitch. If your frame is wider than 34" you will need to...
  view full answer...
• Recommendation for Class 5 Hitch to Fit 1995 Ford F350 with 34 Inch Frame and Flat Dump Bed
  Based on the size of your frame, it sounds as though your 1995 Ford F350 is the Cab and Chassis style. Curt offers a Class IV Receiver Hitch, # C14082, that with bolt directly to your vehicle's frame with no welding required. This hitch has a 1000 pound tongue weight capacity and 10000 pound towing capacity. We do not offer a custom Class V hitch for your truck but universal Class V hitch receivers are available. Curt offers the Universal Weld-On Receiver, # 15901, with 3 inch drop and...
  view full answer...
• Hitch that Fits 1977 Ford F-250 with Narrower Frame
  Sounds like you have a cab and chassis model Ford F-250 which has frame dimensions of 34 inches measured from outside to outside which we have hitches for like the Curt # C14082 but there is drilling required to install this hitch as well as any other hitch that would fit your truck.
  view full answer...
• Recommended Trailer Hitch For 1990 Chevrolet Silverado 4WD Short Bed
  I have another option for you, but the Curt C15322 (now # C15323) is only confirmed to fit select 1999-2014 Chevrolet Silverado's and GMC Sierra's and will not fit your 1990 Chevrolet Silverado 4WD Short Bed. Instead I recommend the Curt Trailer Hitch Receiver - Custom Fit - Class V XD - 2" # C15325 which is confirmed to fit your truck as long as it is has the standard or step bumper and is not a crew cab. If your truck is a crew cab then you will need the # C14082 instead. I included...
  view full answer...
• Does the Curt #14082 Require Modification to Work with Under Bed Mounted Spare Tire?
  Yes. I've linked a picture of a Chevy C Series with the under-mounted spare tire to show you, but the Curt # C14082 will work with the stock spare tire mounting location on your 1971 C Series pickup and you won't need to make any modifications as long as your truck has 34" frame spacing. If your 1971 C10 has a frame with different width, please let me know and I can recommend a universal hitch that will work for your truck.
  view full answer...
  
• Trailer Hitch Receiver For a 1958 Chevrolet C10 With 8' Bed, Step Bumper and Spare Tire
  I recommend the Curt Trailer Hitch Receiver # C14082 for your 1985 Chevrolet C10 pickup with the 8' bed. This is a class IV receiver and will require you to drill 6 mounting holes in your 34" wide frame rails. The maximum trailer weight capacity of the receiver is 12,000lbs and 1,200lbs of tongue weight with a weight distribution hitch. Without a weight distribution hitch, capacity decreases to 10,000lbs and 1,000lbs of tongue weight. Be sure to not exceed any towing ratings give by Chevrolet...
  view full answer...
• Distance from Mounting Bracket to Top of Receiver on Curt Trailer Hitch # C14082
  The measurement from the top of the mounting bracket down to the top of the receiver tube measures 5 inches. Curt trailer hitch # C14082 is a custom fit hitch designed to fit the following vehicles: 1973 - 2000 Chevrolet C/K Series Pickup Cab and Chassis 1973 - 2000 GMC C/K Series Pickup Cab and Chassis 1973 - 1983 Ford F-100, F-150, F-250, F-350 Cab and Chassis 1984 - 1991 Ford F-150, F-250, F-350 Cab and Chassis 1992 - 1996 Ford F-250 and F-350 Cab and Chassis If you have a different...
  view full answer...
• Will Spare Tire Interfere with Trailer Hitch Installation on a 1978 GMC C/K Series Pickup Truck
  The Curt trailer hitch # C14082 is designed to attach to the bottom of a 34 inch wide frame on a cab and chassis model 1978 Chevy C/K series pickup. If the spare tire fits between the frame rails then it will not be a problem, otherwise it would need to be relocated or the mount modified. If you do not have a cab and chassis model truck this hitch will not fit. I have linked the instructions for you to view. I have also linked the other hitches for your truck in case you do not have a...
  view full answer...
• Trailer Hitch Recommendation for a 1985 GMC C10 Short Bed 2WD
  The Class V Ultra Frame Trailer Hitch Receiver # 41947 is compatible with a 1985 GMC C/K Series Pickup with either the 8' bed and standard or step bumper, or a cab and chassis model. Since you have a short bed on your C10 I recommend going with the Class IV Curt # C14082 which fits the 6' bed that utilizes a standard or step bumper. This is a custom fit that doesn't require drilling and fits as long as your frame is 34" outside to outside. If you used to have the standard or step bumper...
  view full answer...
• What Vehicles Does The Curt Class IV - 2" Trailer Hitch C14082 Fit?
  The Curt Class IV - 2" Trailer Hitch # C14082 fits a pretty long list of vehicles, but I have them all listed below. Just be aware that your vehicle must have 34" frame spacing (measured outside to outside) for it to fit properly. 1963 - 1980 Chevrolet C/K Series Pickup 6 Foot Bed with Standard Bumper 1981 - 1987 Chevrolet C/K Series Pickup 6 Foot Bed with Standard or Step Bumper 1963 - 1980 Chevrolet C/K Series Pickup 8 Foot Bed with Standard Bumper 1981 - 1987 Chevrolet C/K Series Pickup...
  view full answer...
• Selecting a Bolt-On/Non-Weld Trailer Hitch Receiver For a 1990 Ford F-Series Super Duty Truck.
  First we will need to determine which style F-Series Super Duty your 1990 truck is. For a Cab and Chassis model you will need the Curt Trailer Hitch Receiver # C14082. For a Super Duty with Deep Drop rear bumper you will need the Curt Trailer Hitch Receiver # C15511. And Finally for the Super Duty with standard step bumper the B&W Heavy-Duty Trailer Hitch Receiver # BWHDRH25122. All 3 of these will require drilling into your frame for a non-weld installation. Each will require you to position...
  view full answer...
• Trailer Hitch Receiver Recommendation and Wiring For a 1990 Ford F-350 Ambulance
  For your 1990 Ford F-350 Ambulance I recommend the Curt Trailer Hitch Receiver # C14082. This receiver is specifically designed for the cab and chassis like that which your Ambulance was built on. This receiver is rated for 1,000lbs of tongue weight and 10,000lbs of trailer. If you use a weight distribution hitch the rating increases to 1,200lbs of tongue weight and 12,000lbs of trailer weight. If you plan on doing any towing and do not have any trailer connection wiring already on your...
  view full answer...
• Availability of a Trailer Hitch to Fit a 1974 Ford F-250 4x4 Crew Cab
  For your 1974 Ford F-250 Crew Cab, the Curt Trailer Hitch, # C14082, is designed to fit the Crew Cab model pickup. This hitch will fit a frame that measures 34 inches wide outside to outside. This Hitch is a Class IV hitch with 10,000 lbs gross trailer weight and 1,000 lbs tongue weight rating.
  view full answer...
• What Grade of Hardware Comes with 10k Hitch for 1977 Ford F-250 C14082
  For a hitch that has a 10k capacity that fits your 1977 Ford F-250 you would want the Curt hitch part # C14082. The hardware that comes with this is Grade 5.
  view full answer...
• Receiver Hitch Recommendation for 1954 Ford F-250 Truck
  Curt and Draw-Tite don't list any specific hitch fits for a vehicle that old, but luckily enough, cab/chassis trucks typically use a 34 inch wide frame and there are tons of those available. I'd recommend the Curt # C14082. This Class IV hitch has a 12K towing, 1K tongue weight capacity. To absolutely confirm the fit, before ordering you'll want to measure the height difference (also known as the drop) between the underside of the frame member and the underside of the rear bumper (if there...
  view full answer...
• Will Curt Trailer Hitch Fit with Flat Bed on 1984 Chevy K20
  The top of the receiver for the Curt Trailer Hitch # C14082 is going to sit roughly 4" lower than the frame on your 1984 Chevy K20. I'm not sure what the dimensions of your flat bed are, but if the part of your flat bed that you're talking about is more than 4" lower than the frame on your pickup then it definitely won't fit. If it's less than 4" then you should be good to go!
  view full answer...
• Trailer Hitch Receiver For a 1978 Chevy K10 Which Allows Spare Tire To Be Mounted Under Bed
  The Curt Trailer Hitch Receiver # C14082 will allow you to keep the spare tire located under the rear of your 1978 Chevrolet K10. This receiver is confirmed to fit either the 6' or 8' long bed with the factory step bumper. I have included an image below showing this receiver on a similar GMC with the spare tire still in place. The T-One Vehicle Wiring Harness # 118311 will give you a 4-way flat connector. This is most common connection on small utility trailer. For larger trailers you...
  view full answer...
  
• Trailer Hitch for a 1997 Ford F-250/F-350 Cab and Chassis Model
  For 1997 a cab and chassis model would have an outside to outside frame width of 34 inches. If that is the case you can use # 13028 which is for the cab and chassis models. Cab and chassis hitches for the 1997 F-250 or F-350 appear in the same list as the regular pickup models so that is probably why you didn't see it. We also have hitch # C14082 for the cab and chassis models. The difference between these hitches is the capacity. Hitch # 13028 is rated for 600 pounds tongue weight and...
  view full answer...
• Class III and IV Hitch Recommendation to Fit 1978 GMC Sierra with 34 inch Frame
  Since you said you have a 34 inch frame that means the hitch you'd need will need to be one intended for cab and chassis models. For that we have the Curt # 13028 for a Class III and the part # C14082 which is a Class IV.
  view full answer...
• Trailer Hitch for 1998 GMC C/K 3500 Cab/Chassis with Dual Rear Wheels
  We've got you covered. The cab and chassis models did indeed have a 34 inch frame width. I'm not sure what kind of capacity you're needing, but because it's a dump truck on a 1 ton chassis, I'll give you a medium and a heavy duty option. For a heavy duty option with a 15000 lb towing capacity/1500 lb tongue weight capacity, I'd recommend the Curt Class V hitch, part # C15511. If you don't need quite that much grunt, Curt offers the Class IV # C14082 with a 10K towing/1000 lb tongue weight...
  view full answer...
• Trailer Hitch Receiver and Vehicle Wiring Harness For Towing With a 1972 Chevrolet K10 Pickup Truck
  Yes, the Curt Trailer Hitch Receiver # C14082 will fit your 1972 Chevrolet K10 Pickup with either a 6' or 8' bed that has a standard step bumper. You can verify that it will fit by measuring the distance of your drivers to passenger side frame rails. It should be 34" from outside of the driver side frame rail to outside of the passenger side frame rail. The Curt Vehicle Wiring Harness # C58044 and Universal Installation Kit # ETBC7 will give you the wiring needed to install a functioning...
  view full answer...

Do you have a question about this Trailer Hitch?