Trailer Weld-on Stake Pocket - 7 Gauge
(90 reviews)
Price: $3.64
In Stock
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Need help with installation?
Locate installers near me- All Info
- Reviews (90)
- Q & A (0)
- Videos (1)
- Photos
etrailer Tie Down Anchors - TSW-A1800
- 2 x 4 Stake Pocket
- Stake Pockets
- Trailer Tie-Down Anchors
- etrailer
Utility trailer stake pocket for use on truck or trailer flat beds. Designed to accept standard 2" x 4" stakes.
Features:
- Solid steel construction
- Raw finish is ideal for welding
- Works with standard 2" x 4" stakes
Specs:
- Inner dimensions: 3-5/8" wide x 1-5/8" deep x 3" tall
- 7-Gauge thickness
TSW A1800 Trailer Weld-on Stake Pocket
Video of Trailer Weld-on Stake Pocket - 7 Gauge
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Video Transcript for etrailer Tie Down Anchors - Trailer Tie-Down Anchors - TSW-A1800 Review
Speaker 1: Today we're taking a look at a trailer weld-on stake pocket. This product allows you to add a stake pocket to your truck or trailer. Stake pockets are great for inserting a two-by-four board to create maybe a side wall. Stake pockets also allow you to have an extra tie-down point. Again, this one's ideal for welding onto the side of your trailer or your flatbed truck. It's made from a solid steel construction.
The raw finish is ideal for welding, so it's ready to be welded directly onto your application. It is designed to work with a standard two-by-four board.Few measurements to go over with you real quick. We're gonna take a measurement from outside edge to outside edge right here. That measures four inches. Inside edge to inside edge you can see is pretty close to three and a half inches.
This measurement right here is one and seven-eighths inches, so that's actually how far it sticks out from the installation surface, not including your welds.It's a nice design, but again, we're just gonna go over the outside measurements here. We have three inches tall, again, four inches wide, one and seven-eighths inches deep. Internally, the opening, again, that's gonna measure about three and a half to three and five-eighths inches. Then from this piece right here to the opening at the back, that's about one and eleven-sixteenths inches.That's gonna do it for today's look at the trailer weld-on stake pocket. Again, it's made from durable solid steel, and the thickness is seven gauge..
Customer Satisfaction Score:
99% were satisfied with this product
1% of customers were not satisfied
- Wrong item was ordered
Customer Reviews
Trailer Weld-on Stake Pocket - 7 Gauge - TSW-A1800
Average Customer Rating: 4.7 out of 5 stars (90 Customer Reviews)
Utility trailer stake pocket for use on truck or trailer flat beds. Designed to accept standard 2" x 4" stakes.by: Jack07/14/2023
The etrailer tie down cuffs were a perfect fit for our wooded sides for our trailor. They welded up great and should last forever.
by: Dale 01/30/2024
Shipping was fast and weld on stake pockets were reasonably priced
by: Les 02/27/2023
Great product saves a lot of fabricatio n.
by: Dennis 03/19/2024
Good quality, is what I needed for this project.
by: James 09/11/2023
Works well in conjunction with other products from Eteailer.
by: Donald 09/16/2023
I looked around and found your product to have the best price and just what I needed. I would recommend this stake pocket to everyone. Fast shipping also. Thanks.
by: Wayne 11/13/2023
Very good company to work with fast shipping very honest
by: Jonathan 10/25/2023
Great looking product and arrived very quickly!
by: Robert 08/05/2023
WORKED PERFECT FOR MY FAB JOB
by: Jim04/13/2019
Although the shipping was quick. I was disappointed as I started welding these on to find that they are more of a parallelogram and are not square. Welding them on square and flush one one side, the other side was still square, but an 1/8 or more lower on the other side my
by: Russell12/15/2022
Exactly what I ordered shipping was extremely fast I've dealt with your store many times and I've never been disappointed even when I had a problem they took care me
by: Dogs Domain Fence05/07/2023
Great price! Welded on fine
by: Chris08/08/2019
They look good, but the size varied. I didn't check to make sure a standard 2x4 fit each one before welding them on. Now i have a few stake pockets that won't fit a normal 2x4 without trimming the end. Be careful and check the size if you buy.
by: Roy 05/09/2020
What can I say.
Etrailer had the part I needed at a very reasonable price , so I purchased it.
The part is exactly as described on their website.
It will be welded to my trailer for a tie-down.
by: Dane11/27/2018
Was trying to figure out a custom way to put stake pockets on my flat bed project. For the price of these stake pockets I couldn’t buy the steel and mess around trying to fab them. No brainer in my mind. Always have had good service from E Trailer.
by: John09/23/2019
Completely restored our 1987 8x 10 trailer, turned out great. I found all the required parts from etrailer. Shipping was fast. etrailer was excellent to deal with. Thanks etrailer, best regards
by: Chris04/25/2018
etrailer is on the ball. Shortly after I entered my order, George J. emailed me to let me know my shipment was on the way. I just received the parts, and they are just as advertised. George followed up to make sure I was satisfied. Great job.
by: Robert06/23/2020
Exactly what I expected, Quality tires at a fair price. Easy ordering and fast shipping. I will continue to use etrailer in the future and recommend this online retailer.
by: James 11/26/2019
Exactly what I needed and best price I found. I ordered Friday evening and my order was on my doorstep Tuesday afternoon. Any items I need for my trailers will be purchased through etrailer from now on excellent selection, price, and service.
by: Steve A01/29/2020
Great weld on stake pocket at a great price. What more can you ask for!
by: Michael 08/09/2021
This was an economical way to add a stake pocket to my trailer.
by: Mark Adams09/09/2018
Good quality material was used to make this part. I was little disappointed with the shape edges that could possible cut a tie down. But for a the price, I just hit them on a belt sander and welded them on.
by: Robert11/14/2018
I found these and were just what I needed and the price was great! I couldn't buy the steel to make them for what they cost. I received an email less than two hour after I ordered them that they were shipped. Got them in two days! outstanding service and products at etrailer. I have purchased from them before and will do so again.
by: Jason05/07/2018
Fits the 2x4 perfectly as stated. Welded the stake pockets on over the weekend and they are perfect. Just what I wanted. Thank you
by: Loren05/04/2021
Very happy with the quality and fast shipping from etrailer.
25
90
Show More Reviews
See what our Experts say about this etrailer Tie Down Anchors
- Stake Pockets for Utility TrailerWe carry a number of stake pockets and you can choose the correct one for your application in terms of size and weld or bolt on. The bolt-on option is the CE Smith Stake Pocket # CE45004G which is 3-1/2" long x 1-1/2" wide x 2-1/2" tall, has a stake pocket opening of 3-1/2" wide x 1-1/2" deep and 3/8" diameter mounting holes. For weld on stake pockets there is the Curt # C83072 which is 4-1/8" long x 1-7/8" wide x 3" tall; the etrailer # HW03-080 which is 3-9/16" wide x 1-9/16" deep x...
view full answer...
Info for this part was:
Written by:
Lindsey S
Installed by:
Cole B
Edited by:
Michael B
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Product Experts Available Now!
Call 1-800-940-8924
Les
2/28/2024
Still working great!