T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector

See what our Experts say about this Tekonsha Custom Fit Vehicle Wiring

• Trailer Lights Flash with Vehicle Flashers and Go Out when Stepping on the Brakes
  So it sounds like the flashers are tied into the running light circuit on the truck side. I am not sure it this is how it is supposed to be or if there is a wiring issue on the truck. The correct 4-Way for a 1998 GMC C/K series is # 118315. It just plugs in line with the vehicle tail light harness, see instructions link. Applying the brakes may be causing the trailer lights to go out while the flashers are on because it is too much draw on the wiring which is causing the lights not to...
  view full answer...
• Fit of Tow Ready T-One Connector # 118315 on 1989 Chevy K1500 w/ Custom Bumper
  The Tow Ready # 118315 is designed to fit a 1989 Chevy K1500 with a stock bumper. The lamps on your bumper should plug into the factory wiring harness on the driver's side frame rail. The # 118315 will plug inline at that connection as long as it hasn't been altered. If your connector looks like what's shown in the photo and video I've linked for you, the # 118315 should fit without cutting or splicing.
  view full answer...
• Connection Point for T-One Vehicle Wiring Harness 4-Way Trailer Connector # 118315, 1998 GMC Pickup
  The T-One Vehicle Wiring Harness with 4 Pole Trailer Connector, # 118315, is a fit for your 1998 GMC pickup. The connection point could be difficult to find unless you know where to look. What you are looking for is a connector that leads to your taillight wiring. It should be located along the driver side frame rail near the bumper. I have included a link to the installation instructions below.
  view full answer...
• Will Curt Trailer Hitch be Hidden Behind License Plate on 1997 Chevy C/K Pickup with Roll Pan Bumper
  Yes, the Curt Trailer Hitch, # 13942, will be hidden behind the spring loaded license plate on your 1997 Chevrolet C/K Series Pickup with a roll pan bumper. I have included a link to the installation instructions for this hitch for reference. This is the only hitch specifically designed for use if the truck has a roll pan. For wiring, you will need Tow Ready Custom Fit Vehicle Wiring, # 118315. I have included a link to the installation details and video for reference.
  view full answer...
• How Can You Tell if a 1997 Chevrolet Silverado Has Factory Trailer Wiring
  The 1997 Chevrolet Silverado has some of the wiring in place to connect a brake controller, but it does not have the provision for plugging the controller in under the dash. There is an orange and blue wire that is run from the rear drivers side frame rail to the engine compartment. The blue wire carries the brake controller output, and the orange wire if for the 12 volt trailer lead. The ends of these wires would connect to the trailer connector at the rear of the truck. In the engine...
  view full answer...
• Will 4 Pole to 5 Pole Trailer Wiring Adapter Fit a 1995 GMC C/K Series Pickup Truck
  Yes, all you will need is to plug the 4-Way end into an existing 4-Way on your 1995 GMC pickup and then use the included quick splice connector in adapter # 20036 to connect the blue wire to a reverse light wire on the truck. Then it will activate the electric reverse lockout on the surge coupler when the truck is put in reverse. If you need to add a 4-Way to the truck you can use # 118315.
  view full answer...
• 7-Way and 4-Way Recommendation for 1993 Chev C1500
  For your 1993 Chevy C1500 you'd want to start with the 4-Way kit part # 118315 which is a confirmed fit and then to convert it to a 7-way/4-way combo you'd just need the # 37185 and you'd be set.
  view full answer...
• Trailer Wiring Harness for a 1994 GMC C/K Series Pickup Truck
  In 1994 the Sierra was just a trim level of the C/K series GM trucks. It wasn't until 1999 that the Sierra started to take the place of the C or K designation and that transition was complete in 2000. For a trailer wiring harness that will fit your truck I recommend the Tow Ready harness # 118315. It plugs in line with the vehicle tail light wiring. I have linked a video showing an example installation for you. A mounting bracket such as # 18144 is also recommended.
  view full answer...
• Wiring to Add 5-Way Harness on 1992 Chevy Silverado to Connect to Boat Trailer
  To add a wiring harness to your 1992 Chevy Silverado for your boat trailer you need to first add a 4-flat, the T-One Vehicle Wiring Harness # 118315; I've attached a link showing this harness being installed on a similar truck for you to check out. From there you need an adapter, the Tow Ready 4 Pole to 5 Pole Trailer Wiring Adapter # 20036 to give you a 5-flat on your Silverado.
  view full answer...
• Recommended Trailer Hitch Receiver For 1995 GMC Sierra K1500
  As long as the tire on the 20" spare is the height as the factory tires on your 1995 GMC Sierra K1500, and your truck has the standard or step bumper you will be able to use the Draw-Tite Trailer Hitch Receiver - Multi Fit - Class IV - 2" # 37130. This hitch has a 700lb tongue weight rating and a 7000lb trailer weight rating when NOT using a weight distribution system, or 1200lb tongue weight and 12000lb trailer weight if you are using a weight distribution system. Keep in mind that these...
  view full answer...
• Trailer Hitch Recommendation for a 1996 Chevy C/K Series 1500 Pickup Truck with Dual Exhaust
  The Curt Trailer Hitch, # 13942, is designed to fit if the truck has a roll pan. There is no restriction if the truck has dual exhaust. I have included a link to the installation instructions for this hitch for reference. This is the only hitch specifically designed for use if the truck has a roll pan. I have included a link to all of the trailer hitch options for a 1996 Chevy C/K 1500. Just select your specific truck style from the pull down menu under where it reads Select Vehicle Style...
  view full answer...
• Recommended Trailer Wiring Harness For 1992 Chevrolet 1500 Pickup Truck
  To add an additional 4-way connector on the 1992 Chevrolet 1500, I recommend the T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector, part # 118315. This plugs into the connection points along the frame rail under the truck on the driver side. There is no cutting or splicing into the truck wiring to install this. When working with electrical connectors I recommend using dielectric grease like part # 11755. This keeps dirt and moisture out of the electrical connections and...
  view full answer...
• Will Draw-Tite Trailer Hitch Fit 1996 Chevrolet C/K Pickup With Step-Side Bed
  The Draw-Tite Max-Frame Trailer Hitch Receiver, part # 75099 is designed to work with all models of the 1996 C/K pickups with a standard or step-bumper, so it will work fine with your step-side. This is a Class lll hitch and it has a 2-inch receiver opening. If you plan on doing some towing you might be interested in etrailer ball mount kit # 989900. It comes with 2 ball mounts; one with a 3/4 inch rise or 2 inch drop and one with a 2-3/4 inch rise or 4 inch drop. It also includes a 1-7/8...
  view full answer...
• Determining the Function of a Wire Labeled YEL FEED BRK SW on a 1994 Chevy C/K2500
  The wire you are referring to is probably the center high mount stop light wire or CHMSL. This wire would be used for a third brake light function for example on a camper shell. You can test it by using a circuit tester like # PTW2993. If the wire shows a signal only when the brakes are pressed, and not when the turn signals are on or flashers are engaged, then it is the CHMSL. If it does show a signal with the blinkers and flashers then it is a taillight brake light wire that also carries...
  view full answer...
• Troubleshooting Trailer Wiring Issues When Vehicle Headlights Are On
  It sounds like there is too much of a draw when your headlights are on and that makes everything else work improperly. There are two possibilities, but it sounds like a bad ground wire versus a bad wiring harness. I recommend checking your ground to make sure it is free of corrosion and rust and has a bare metal to metal connection. One easy way to test this is to take a length of wire and just connect it to your negative battery terminal and then the location of your ground wire on...
  view full answer...
• Power Wire for a 7 Way on a 1996 Chevy Pick Up
  If your 1996 Chevy pickup did not come with a factory 7 way, you will need to run a power wire from the battery back to a 7 way that you will install. However, if your trailer does not need an auxiliary power supply, you can omit running the power wire up to the battery. I assume you will be needing to add a 7 Way plug. If you already have a 4 Way trailer connector, you will simply need part # ETBC7 to complete the installation of a 7 Way. If you do not already have a 4 Way connector...
  view full answer...
• Trailer Wiring Does Not Work on a 1999 Chevy Silverado or C/K Series Pickup
  Does the converter you are using by any chance require a direct connection to the vehicle battery to actually power the trailer lights? Some converters are powered and they get the signals from the tail light wiring but the power comes from the vehicle battery. It could also be a bad converter box. Use your test light to test the wires going into the converter box to make sure they are correct. If they are not correct that indicates a problem with the truck wiring. If they are correct...
  view full answer...
• Adding a 4-Way Flat Trailer Connector to a 1992 Chevrolet C/K Series Cab and Chassis
  A 9-pole to 4-Way flat adapter is not available since it is a combination that is quite rare. You would either have to make one or install a separate 4-Way. The easiest solution would be to install the Tow Ready Custom Fit Vehicle Wiring, # 118315. I have included a link to the installation instructions for you. The 4-Way plugs in line with the tail light wiring on your 1992 Cab and Chassis model Chevy C/K.
  view full answer...
• 4 Pole Trailer Wiring Harness for 1991 Chevy C/K Pickup Truck
  The Converter # HM48925 is indeed designed to tap directly into a vehicle's taillight circuits. Your truck uses a combined wiring system, so the converter box would be providing circuit protection to isolate the truck wiring from any short circuits that might occur in the trailer wiring. To install, the green wire taps into the right turn circuit, the yellow wire into the left, the brown into the taillights and the red and the while would be grounded to the truck. There is a plug and play...
  view full answer...
• Parts Needed for Trailer Brake Controller Installation on 1998 GMC C/K Series Truck
  The 1998 GMC and Chevy C/K series trucks weren't prewired for a brake controller like the newer trucks were, so you'd need to hardwire the controller which is a pretty simple process. Along with the # 39523 brake controller, you'll also need the # ETBC7 brake controller installation kit. If you don't already have a 4-pole trailer connector to tap into the lighting circuits, you'll also need a T-connector, part # 118315. The install kit includes all the wire, circuit breakers and hardware...
  view full answer...
• Recommended Equipment Needed to Add a 7-Way and Brake Controller to a 1994 Chevy Silverado 1500
  We have exactly what you need to install on your 1994 Chevrolet Silverado 1500 to activate your trailer lights and use a brake controller for the trailer brakes. Although the ModuLite on wiring harnesses can be very helpful, it isn't really necessary on vehicles that were built with towing in mind. The only time you really need to use a harness with a ModuLite is when you are installing it on a car. For your Silverado I recommend installing the Tekonsha T-One # 118315 which will install...
  view full answer...
• Parts Needed To Install a Trailer Brake Controller On a 2000 Chevrolet 3500HD Cab and Chassis
  Yes, you can add a trailer brake controller to your 2000 Chevrolet 3500HD cab and chassis as it does not any pre-wiring from the factory. The Universal Installation Kit for Trailer Brake Controller # ETBC7 will provide you with the wiring needed to install a trailer brake controller. I was able to find a installation video of this with a Tekonsha Prodigy P3 Trailer Brake Controller # 90195 being installed on a 1997 Chevrolet Flat bed that will be similar to your cab and chassis. The T-One...
  view full answer...
• How To Install The Tekonsha Prodigy P2 Brake Controller # 90885 On A 1997 GMC 2500 2WD Truck
  To install the Tekonsha Prodigy P2 Brake Controller, part # 90885, on your 1997 GMC 2500 2WD truck, some models do have the brake (blue) and hot lead (orange or red) wires already ran from under the hood to the end of the driver's side frame rail. However, these wires are hard to access and additional wire will still be needed. The easiest way to install the Prodigy brake controller on your 1997 GMC 2500 truck is to use the Tow Ready T-One Wiring Harness, part # 118315, and the Brake...
  view full answer...
• How to Install an Electric Brake Controller Unit on a 1998 Chevrolet Pickup
  For your 1998 Chevrolet Pickup, there is no brake controller connector on the vehicle so the wiring for the brake controller will have to be hard wired on the vehicle. You will need just a few items to install a brake controller on your pickup. The items you need are a Working 4-Way connector, item # 118315, if you do not already have one. A brake controller wiring installation kit, item # ETBC7, and a brake controller of your choice. I would recommend the Prodigy P2, item # 90885 for...
  view full answer...

Do you have a question about this Custom Fit Vehicle Wiring?