Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Light-duty, rust-resistant bracket lets you mount a bunk board on its side and enables the board to pivot. Mounting slot allows for height adjustment. Dimpled surface keeps bracket from sliding along the trailer frame.
Features:
Specs:
Typically mounted upright on a boat trailer's crossmembers, vertical bunk brackets allow you to mount a bunk board on its skinny side and run the board from the front of the trailer to the back. On kayak trailers, these brackets are mounted to the trailer's frame and support bunk boards that run across the trailer.
Galvanized Steel
Galvanized steel parts are hot-dipped in zinc after being stamped. This creates a coating that is typically 3 mil to 5 mil thick. This thick, all-around coating allows galvanized steel products to provide years of use without rusting or corroding.
California residents: click here
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Hello, everybody. This is Jeff at etrailer.com. Today, we're gonna take a look at the CE Smith 8 1/2 inch tall, galvanized steel, light-duty, vertical bunk bracket. Now, this light-duty bunk bracket will let you mount a bunk board on your boat trailer. This is ideal for two by four or two by six bunk boards on small craft trailers. This basically will enable the bunk board to pivot during loading.
And right up here, these two holes, these are the bunk board mounting holes. The diameters on those holes is 7/16 of an inch. This will stabilize your bunk board when there's two brackets being used. If you notice on this bracket, it has two slotted mounting slots here, which will permit as much as about 5 1/2 inches of height adjustment during installation. This bracket does install vertically on your boat's trailer frame with a U-bolt.
Now, the U-bolts that go in here, we do sell those separately. Total height on this, we go from the bottom to the very top is gonna be right at 8 1/2 inches. Total width on it, gonna be right at two inches wide. Now, the mounting slot, you can see there's two of them. The width on the slot is gonna be a half an inch.
And the length on each one is right at 2 1/2 inches long. Now, this is an 11 gauge galvanized steel, which will resist rust and corrosion. The thick all-around coating on this allows the galvanized steel products to provide years of use without rusting or corroding. This part is made in the USA. And this is for a quantity of one bracket.
But that should do it for the review on the CE Smith 8 1/2 inch tall, galvanized steel, light-duty, vertical bunk bracket..
Average Customer Rating: 4.5 out of 5 stars (23 Customer Reviews)
Light-duty, rust-resistant bracket lets you mount a bunk board on its side and enables the board to pivot. Mounting slot allows for height adjustment. Dimpled surface keeps bracket from sliding along the trailer frame.The product was as advertised, good quality, and shipping was expedient!
Nice heavy-duty part.
Exactly what I needed!
etrailer has everything I need to upgrade an old trailer that I inherited. Good quality products, great prices, and quick shipping. Thanks etrailer!
great won't rust
Your trailer parts are the perfect fit for the boat trailer! Using the trailer and boat in primarily salt waters so far have shown no breakdown to the bunk supports. I am sure with proper wash downs after use will continue to extend the life of those parts. Thanks for your products.
The bunk brackets were if good quality and fit directly in place of the old ones. I would have given it a 5-star rating if the part had a somewhat more quality feel, but it is functionally excellent and I have no complaints. I will buy these againew when I need another set.
I used these to mount the L brackets that ultimately supported the bunk boards. They are still working great, haven't moved or anything.
The parts arrived in a timely fashion and fit perfectly. I would definitely shop with you again in the future. Thanks to etrailer!
Sturdy, and the right fit for my trailers configuration.
Good replacement part. Was just a little wider than the one I was replacing.
The brackets would be perfect if they were only 1 3/8 or 1 1/2 inches wide since a 2x4 or 2x6 is roughly 1/38 wide. Now I have to make some shims.
ALWAYS dependable, quick, easy to acces s.
Patrick M.
6/30/2020
So far, so good. The boat and trailer were in rehab status, so there has been only static loading. Ive finished the boat and will be putting all parts to the test with live loads, soon.
This product arrived in a timely manner, was well constructed and perfectly fit my needs.
Great
Jeff M.
5/14/2014
Great
The lady who took my order was very helpful, friendly sounding, and professional. A pleasure to do business with!
Product was exactly what I needed and it was shipped in a timely fshion.
Very good product, well made!
MORE HEAVIER DUTY THAN THE ORIGINAL !
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Michael G.
4/1/2021
Great products and very quick service