Universal-Design Rocker Switch - SPST - On-Off - 12 Volt - 20 Amp - 3-Blade - Red Pilot Light

See what our Experts say about this Pollak Accessories and Parts

• Is Light of Universal-Design Rocker Switch # PK34360 LED
  Yes, the illumination light of the Universal-Design Rocker Switch # PK34360 that you referenced is LED.
  view full answer...
• How to Wire the ThermaHeat RV Holding Tank Heater Pad To an On/Off Switch
  There are two wires coming from the ThermaHeat RV Holding Tank Heater Pad part # 277-000164. There is a red wire for the 12 volt power and a white wire for the ground. This heating pad draw's 4.8 amps of power. Therefore, if you will be attaching three of these to a single switch then the switch will need to be rated for 14.1 amps (4.8 x 3). For a switch, I recommend using the Universal-Design Rocker Switch part # PK34360 which is rated at 20 amps and will be sufficient for three of the...
  view full answer...
  
• Running Wires For Hopkins Backup Camera To Mount On Front Of Vehicle
  In order for you to be able to use the Hopkins Smart Hitch Backup Camera, part # HM50002 as a camera and monitor, you will need to cut the plug off the end and hard wire the system. If you are going to use it for the front I recommend running the red wire to the battery and use a switch. You will need additional wiring like part # DW07550-1 to reach the switch inside of the vehicle. This is sold by the foot. You will also need to secure the white ground wire to a clean bare metal surface. For...
  view full answer...
• Can The Furrion Vision S Camera System Be Used As A Security System?
  It sounds like your 2021 Forest River Sandpiper 321RL has the Furrion Vision S Wireless RV Observation Camera System w/ Side Marker Light Cameras # FCE48TASL-05, which if that's the case, then yes you can use the Replacement 7" Monitor for Furrion Vision S Wireless RV Camera System # FR97FR to pair to your existing cameras. To pair your cameras, you will need to press and hold the pairing button on the cameras for 10-15 seconds to begin pairing process. From here, you will: 1. Use...
  view full answer...
• Wiring Multiple Heater Pads to an On/Off Switch
  For starters, I have attached a photo of how the Universal-Design Rocker Switch part # PK34360 should be wired. However, I believe the issue you are having is in regards to the size of wire used. The correct size or (gauge) will vary depending on factors such as amp draw and length of wire. The wires running from the heater to the splice can be anywhere from 16 gauge - 10 gauge depending on length. However, once the three heater wires are spliced together and traveling to the switch you...
  view full answer...
  
• Can a Switch be Used with Interior Light part # ILL85CB
  You definitely could wire a switch on either the power or the ground wire of the part # ILL85CB. For a rocker style switch with a lighted switch the part # PK34360 would be a great option.
  view full answer...
• Redarc In-Vehicle DC DC Battery Charger Installation To Select When The Charger Is Activated
  Since you are going to use the Redarc In-Vehicle BCDC Battery Charger # RED96FR only when you are stationary you would need to connect the red wire to a alligator clip as you suggested or I recommend a Rocker Switch # PK34360 to the 12 volt circuit in your motorhome to allow you more conveniently be able to switch it on and off from your dash when you run your motorhome and want to charge its batteries. The blue wire of the Redarc charger controls the charging profile of the charger....
  view full answer...
• Recommended Interior LED Lights for Cabin
  We have a large selection of interior LED lights that will work great in your newly built cabin. I recommend looking at the Optronics LED RV Interior Light # RVILL34. This is a very nice and bright surface mount light that measures 10-5/16 inches long, 4-3/16 inches tall and 1-13/16 inches deep. It uses 12 gauge wire and includes a power and ground wire coming from the assembly. You can use additional 12 gauge wire like # 12-1-1 (sold by the foot) to make the necessary connections in...
  view full answer...
• How To Wire Furrion Vision S Wireless Observation Camera
  If you are wanting to install the Furrion Vision S Wireless RV Observation Camera System w/ 3 Marker Light Cameras - 7" Screen # FR98NR you were looking at to where it is powered even when your 2019 Keystone Montana Model 3561RL is not connected to your truck, you will not be able to use the use the factory wiring and will need run new wires from each camera directly to the on-board batteries and use a switch like the # PK34360 to turn the system on and off. If you are only wanting the...
  view full answer...
• Using Vision S Camera as Security System
  Technically you can yes but the Vision S is meant to be powered on with the running light circuit so you would have to find a way to wire it from the lights and to a battery using a rocker switch like # PK34360. You'd then need to wire outlet # 37215105 as well to power the monitor. Or you could just use a different type of camera that you can see from your phone like the Swift Hitch Wi-Fi Camera for Smartphone or Table # SH04.
  view full answer...
• Why Did Wires to Rocker Switch Melt When Installing Heating Pad
  If the wire from the battery to the Universal-Design Rocker Switch # PK34360 melted when installing the ThermaHeat RV Holding Tank or Step Heater Pad w/ Thermostat # 277-000163 it may have been that you simply need to use thicker wire, and I recommend 10 gauge # 10-1-1. A lot of things may have come into play to cause this short, particularly the length that the wire needed to be run. It could also have been something as simple as damaged wiring or a loose connection which caused the...
  view full answer...
• Recommended 12V Switches To Replace Interior Light Switches
  i have attached a link to the switched we offer that may work for your light switch. For a single pole/single throw switch for 12V DC systems I recommend part # PK34308. If you prefer a switch with a Red pilot light I recommend part # PK34360. These are rocker design switches. If you want a toggle switch for your lights I recommend part # PK34571.
  view full answer...
• Can Hopkins Backup Camera be Wired Directly to Battery Using an On/Off Switch
  What you can do is attach the power wire for the backup camera # HM50002 to the running light circuit so that you won't have to run any wires or install a switch. Then to operate the camera you would just turn on the running lights. Now, this method will turn the camera on any time your head lights are on so at night it would be on all the time. Just turn the monitor off in that situation! The wiring is not very large gauge with this camera so at most I would say use 16 gauge wire, #...
  view full answer...
• Replacement 12 Volt On Off Rocker Switch
  Yes we do have them. I personally prefer the Universal-Design Rocker Switch - SPST - On-Off - 12 Volt - 20 Amp - 3-Blade - Red Pilot Light # PK34360. The red indicator light lets you know if it is on or off from a distance. If you like the simple standard look we have the Single Rocker Switch - Labeled On/Off - SPST - Black # 37212595. It doesn't have a light indicator it is just labeled with ON/OFF. We also have the Single Rocker Switch - 12V - On/Off - SPST - Black Plate with Blue Illuminated...
  view full answer...
• Recommended RV Observation Cameras That Can Be Used As Security Cameras
  We have just the system you are look for. I recommend the Furrion Vision S Wireless RV Observation Camera System w/ 3 Marker Light Cameras - 7" Screen # FR98NR which has a camera for each side to replace a clearance light, and a camera for the rear of your 2008 Cyclone 3795 which also replaces a clearance light. This system requires wiring for power, but wirelessly communicates with the included 7" monitor allowing you to view all 4 cameras at once for security, or towing purposes. If...
  view full answer...
• When Does Switch Light of Rocker Switch PK34360 Turn On with ThermaHeat RV Holding Tank Heater Pad
  If you used the Universal-Design Rocker Switch part # PK34360 and wired it to the ThermaHeat RV Holding Tank Heater Pad part # 277-000163 like the attached diagram shows the red light will be on anytime the switch is on regardless of if the thermostat. Basically as long as the pads have power the light will be on and then the thermostat will do what's it's designed to do without affecting the switch light.
  view full answer...
  
• Adding ThermaHeat RV Holding Tank Pad to DC Fuse Panel
  Yes, you can use two of the ThermaHeat RV Holding Tank or Step Heater Pad # 277-000163 connected to your DC fuse panel. You could do this with both pads running to individual switches, or if you wired them in parallel you would only need to use one switch, such as the Universal-Design Rocker Switch # PK34360, because the pads draw 4.8 amps and this switch is rated for 20 amps. Essentially, so long as your switch is rated for the appropriate amperage you would run the wire from the fuse...
  view full answer...
• Transmission Heater Pad and Function in Cold Weather
  Kat's says their Silicone pads like # KH23075 will get hot enough they warn that they can burn a person or melt an item that cannot withstand that heat. They however do not give a temperature for that 75 watt model. That is the only 12V option the rest run on 120V and there is one that is larger at 5-1/2 inches by 8-1/2 inches that is 500 watts and claimed to run between 300 and 400 degrees. Unfortunately the questions you are asking about timing, temperature, and consumption can't...
  view full answer...
• Troubleshooting ThermaHeat Heater Pad Not Operating on Sensor Power Wire
  You are probably overloading the circuit with both the sensor and the ThermaHeat RV Holding Tank or Step Heater Pad # 277-000163 on it. We recommend connecting the heater pads directly to your battery for power so that it is the only thing on the circuit (unless you were to connect more than one heater pad). If you want to be able to control when the heater pad is on separately from the thermostat then you can install the Universal-Design Rocker Switch # PK34360 on the power wire between...
  view full answer...
  
• Parts Needed to Add Interior/Exterior Lights and a Battery to a Trailer
  I have attached a basic wiring schematic for a travel trailer for you to check out. We don't have anything that would be more detailed than this but you would basically just splice into the wiring on your trailer depending on how you want your exterior and interior lights to work. Aside from the wiring and lights there are a few other things you will need. The switch that you use will depend on how much draw you expect to have, which is determined by the amount of lights you have and the...
  view full answer...
  
• Wiring and Spade Connectors for Switch for ThermaHeat RV Holding Tank Step Heater Pad
  The ThermaHeat RV Holding Tank or Step Heater Pad w/ Thermostat # 277-000163 only draws 4.8 amps so you can get by with thinner gauge wire like 16 AWG which we sell by the foot with # 16-1-1. For spade connectors to go from the wire to the switch # PK34360 you could then use the # RM-300115-00 and you'd be set.
  view full answer...
• Will the Universal-Design Rocker Switch With Dual Actuators Install In a Standard Switch Cutout
  The Universal-Design Rocker Switch part # PK34312 is a dual actuated switch that gets installed in a 0.830" wide x 1.450" tall cutout which is a very common size. Therefore, yes the above will install inside a standard 12 volt rocker switch cutout. For reference, the Universal-Design Rocker Switch part # PK34360 is a single actuated switch that gets installed in the same 0.830" wide x 1.450" tall cutout as the above. The Female Spade Terminal Quick-Disconnect part # DW01899-1 is what...
  view full answer...
• Is the 12 Volt Circuit on a Vehicles 7-Way Constantly Powered
  Yes, the trucks could have been wired different in which the trailer connector still receives power while the truck is off. This has to do with the 12 volt power circuit that is ran to the trailer connector. If it is wired directly to the battery then it will receive power constantly but if it is tied into a powered switch then it would only receive power while the ignition is on. If you would like to cut power to the vehicle's 7-way when the vehicle is off then you will need to install...
  view full answer...
• Which Pins of the Switch Part # PK34360 Are for Each Circuit
  On the back of the # PK34360 the terminal in the corner with the pin next to it is the power pin, the one right next to it with the silver rivet is the ground. The light terminal is the one opposite of those two in the other corner. I attached a picture that shows the terminals pointed out.
  view full answer...
  

Do you have a question about this Accessories and Part?