Installation Kit for Go Power Inverters - 400 Amp Fuse - 12V and 24V

See what our Experts say about this Go Power Accessories and Parts

• Inverter and Lithium Batteries Needed to Power a Mobile House
  I spoke with our contact at Go Power to get some better insight on this for you. For your inverter, you will need the Go Power Industrial Pure Sine Wave Inverter Charger - 3,000 Watts, part # 34275013. For the installation kit, you will need the Installation Kit for Go Power Inverters - 400 Amp Fuse - 12V and 24V, part # 342GPDCKIT5. Finally, for the batteries, you will need two of the Go Power Sun Cycle Solar RV Battery - Lithium - 12V - 250 Amp Hour - LiFePO4 - Group 4D, part # 34282740. This...
  view full answer...
• How To Wire In Solar Panel Systems And A Go Power IC2000 Inverter Charger
  Hi Robert, Solar panel systems are all going to be ran independently to the battery bank and wouldn't need to tie into the wiring for your Go Power IC2000 Inverter Charger # 34280055. Your solar panels will run to the Go Power MPPT Solar Charge Controller # GP54FR and from there directly to the batteries. Both the solar charge controller and the IC2000 can read the battery charge level and alter the charge that they send to the battery so there won't be an issue wiring them separately.
  view full answer...
• Which Inverter Charger Should I Use For My Keystone Montana RV?
  The yellow wire is the wire that connects to the solar panels. I have attached a detailed wiring diagram and demonstration video for the Redarc In-Vehicle BCDC Battery Charger - Dual Input - DC to DC - 12V/24V - 50 Amp # 331-BCDC1250D. In regard to an inverter/charger with a built-in transfer switch, I recommend going with Go Power Industrial Pure Sine Wave Inverter Charger - 2,000 Watts - 100 Amps - 12V # 34280055 and Installation Kit # 342GPDCKIT4. If you need more than 2,000 watts,...
  view full answer...
  
• Inverter For Solar Panels For Home Application
  While we do have inverters, there are none which will allow you to attach your 4-prong generator plug; you would need to wire from a battery bank to the inverter, and then to your home's wiring. The correct inverter would depend on the wattage you need. For example, for a 3,000 watt inverter you would use the Go Power Industrial Pure Sine Wave Inverter - 3,000 Watt - 12V # 34278157 with the Remote for Go Power Industrial Pure Sine Wave Inverter # 34279999 and Installation Kit for Go Power...
  view full answer...
• Is The Go Power 570 Watt Solar Extreme Charging System Available With a MPPT Charge Controller?
  Since Go Power does not offer a Solar Extreme Charging System like # 34282185 with a 30amp MPPT Controller # GP72RR you would need to get all the components separately and build your own system. Here is a list of the parts needed. Go Power Overlander Expansion Kit # 34282182 Qty- 3 30AMP Go Power MPPT Solar Charge Controller # GP72RR Bluetooth Remote Display for Go Power MPPT Solar Charge Controllers # GP37MR 3,000 Watt Go Power Industrial Pure Sine Wave Inverter Charger # 34275013 Go...
  view full answer...
• Does Progressive Dynamics 60 Amp RV Power Control Center Convert DC to AC
  The Progressive Dynamics 60 Amp RV Power Control Center with AC/DC Panel and Converter/Smart Charger # PD4560K18LS8 does have a built-in converter but if you have some outlets that are designated for AC power then you do need to use an inverter like the Go Power Heavy-Duty Modified Sine Wave Inverter # 34280178. For this you can use the fixed-mount remote # 342GP-HD-R and the installation kit # 342GPDCKIT5 to safely connect the inverter to your battery and monitor your system.
  view full answer...
• Installation of Go Power Industrial Pure Sine Wave Inverter Charger
  The Go Power Industrial Pure Sine Wave Inverter Charger, # 34275013 should be installed using 4/0 or larger wire. Your currently installed converter needs to be supported with wiring that supports this. We have the Installation Kit for Go Power Inverters with 400 Amp Fuse # 342GPDCKIT5 available if needed. This should be installed in close proximity to the battery bank, but not in the same compartment. Wire the DC terminals to the battery bank, installation details are linked below....
  view full answer...
• Parts Needed To Install The Go Power Industrial Pure Sine Wave Inverter # 34278157
  To install the Go Power Industrial Pure Sine Wave Inverter - 3,000 Watt - 12V # 34278157 you'll need some wiring for both the AC output and DC input, a 400 amp fuse, and a 20amp GFI outlet. For the DC input you can use the Installation Kit for Go Power Inverters # 342GPDCKIT5, as it comes with the correct gauge wire and fuse that you'll need for the DC side of this installation. For the AC side you'll need some wire, three ring terminals, and a GFCI outlet to complete the AC side of...
  view full answer...
  
• How To Install The Go Power Industrial Pure Sine Wave Inverter Charger
  There's going to be two ways to wire your Go Power Industrial Pure Sine Wave Inverter # 34275013 but the transfer switch you have between the shore power and generator power is going to stay how it currently is. The internal transfer switch is simply to swap between shore/generator power and inverter/battery power. Option 1 will have you run the line from that transfer switch to the main panel and from there to the inverter. Option 2 will have you run that line from the transfer switch...
  view full answer...
  
• Solar Panel Set Up With 3,000 Watt Inverter & 60 Amp Solar Controller
  We can get you set up with everything you need with the solar panels, 60 amp solar controller, and 3,000 watt inverter charger. That said, the solar panels we offer are 190 watt and not 200 watt, so a total of 760 watts. That said, the solar kit and inverter charger that you need which will work together are the following: - Go Power Solar AE-4 All Electric System with MPPT Solar Controller - 760 Watt Solar Panels # 342-75010 - Go Power Industrial Pure Sine Wave Inverter Charger - 3,000...
  view full answer...
• Will Two 12V Batteries be Enough to Power the 3000W Go Power Inverter # 34275013 for a Short Time
  You can use two 12V batteries to power the Go Power Inverter # 34275013 but that all depends on what size 12V batteries you plan on using what "short periods of use" means. I reached out to my contact at Go Power and he said that if you are using deep cycle batteries and the load is not too excessive then you should be fine. For example, if you were trying to pull the full 3000 Watts out of the inverter that would be about 25 Amps AC or 250 Amps DC. If you were to run this for a half...
  view full answer...
  
• Can Go Power Heavy-Duty Inverter 34280178 Connect to RV Through a Transfer Switch
  The Go Power Heavy-Duty Modified Sine Wave Inverter # 34280178 can connect through a transfer switch to your RV's 12VDC battery bank. Since it has built-in safeguards for over/under voltage, short circuiting, overloading, and over/under temperature it will protect your RV electrical system during power use. It will also display battery wattage and voltage so that you know your power status at any time. You can use the Installation Fuse Block Kit # 342GPDCKIT5 to connect the inverter to...
  view full answer...
• Fuse for Go Power Industrial Pure Sine Wave Inverter
  The correct fuse size for the IC-3000, which we carry with the Go Power Industrial Pure Sine Wave Inverter Charger - 3,000 Watts # 34275013, is 400 amps like you mentioned your old inverter used. You can get the fuse with cables with the Installation Kit for Go Power Inverters - 400 Amp Fuse # 342GPDCKIT5.
  view full answer...

Do you have a question about this Accessories and Part?