Customers compare 319-r7-52 to these similar products
Products Featured in this Video
Speaker 1: Today we're going to be taking look at the easy connectors male to female adapters. For your seven way, part number 319-R7-52 for your six way, part number 319-R7-56, for your five way, part number 319-R7-55 and finally for your four way, it's going to be part number 319-R7-54.So here are our trailer ends, we've got a standard seven blade connector. On our vehicle end, we've… see more >
Info for these parts were:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Videos
Help Articles
Expert Answers
Either way is correct. It depends on if you want to keep the semi-style 7-Way (if you need to tow that type of trailer) or if you will never be towing a semi-trailer. If you need to keep the 7-Way semi active on the truck, then you would need to make…
view full answer...Thanks for the pictures! Since your 2014 Toyota Tacoma has a 7-way connector that is hardwired in you will need to cut the wires from the factory connector and hardwire them to the EZ Connector Magnetic 7-Way Trailer Connectors w/ Watertight Seal -…
view full answer...The wiring on a semi is not normally the same as a standard RV or Gooseneck trailer. You will need to use a couple different harnesses to get what you are looking for. I recommend the ZCI Circuit Protected Vehicle Wiring Harness w/ 4-Pole Flat…
view full answer...For the initial settings when you first start the test drive, you should start with the lowest braking setting on the output of the Curt Echo #C51180. This initial setting is the same no matter the weight of your trailer. When you are testing the…
view full answer...For your 2018 Acura MDX the aftermarket trailer hitch that will be most similar to the OEM/factory unit is the etrailer.com Class III Hitch #e98840. The primary difference between the OEM hitch for the Acura MDX and an aftermarket model is their…
view full answer...There isn't a wedge that can be used with the Q Series Curt fifth wheel hitches. The Q series of hitches cannot be used with Sidewinders as their jaws/head will get permanently damaged. Instead, you'll want to use something like the Curt E16…
view full answer...Curt is the manufacturer of the Mopar branded 5th wheel trailer hitches. For example, the Mopar 5th Wheel Trailer Hitch part 82214742 is the same as the Curt Q20 5th Wheel Trailer Hitch part #C16530-16021 and the Mopar 5th Wheel Trailer Hitch part…
view full answer...The Q Series of Curt fifth wheel hitches can't be used with Sidewinders as the jaws and heads end up getting damaged. Instead, I recommend using the Curt E16 5th Wheel Trailer Hitch - Slide Bar Jaw - 16,000 lbs #C16115 with Wedge #RP64FR. The…
view full answer...I highly recommend checking out the EZ Connector Magnetic 7-Way Trailer Connectors #319-R7-02 because they are extremely easy to use and maintain. Thie EZ Connector comes with the trailer end and vehicle end connectors; you will simply plug in the…
view full answer...The trailer wiring code we mention on our wiring help article (attached) is just a typical wiring configuration and can vary, as we state and can be seen on the attached photo. As long as your 7-Way pinout matches the photo I attached you'll be…
view full answer...If your 7-way harness' locking tab broke you could replace the wiring harness if you wanted to or you can simply snug it up with a zip tie. I suggest that you disconnect the plug from the 7-way, clean the contacts as needed, apply a protective…
view full answer...Though I do have a solution for you, however there isn't a kit that will allow you to convert your MORryde steps to strut assisted steps. The only option that we would have for you is to replace your steps with steps that already have the strut…
view full answer...