Customers compare T1001 to these similar products
Products Featured in this Video
Today we're going to be taking a look at the Valterra RV Waste Valve. This unit simply adds or replaces a waste valve gate in your RV's waste system. It's made from a strong and durable black plastic construction. The valve's going to features 1 1/2 spigot and hub on each side, so it's going to connect between two plumbing pipes. If we take a look on this side first, we're going to go over the… see more >
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Videos
Help Articles
Expert Answers
To find the correct E-Z Flex Equalizer, you will need to take off your current ones and measure the distance from the center of the one end hole to the center of the other. You will also need to ensure that your leaf springs are 1-3/4" wide.…
view full answer...My friends at Lippert have identified your axle as being a 3500 lb axle with a hub face to hub face distance of 88 inches and a 68.5 inch center to center spring seat distance. Given that, we do offer an axle that would work for you with a slight…
view full answer...For the LCI52-SB-86.5-68.5, the two ending measurements are: 1st - measurement from hub to hub, meaning the length of the axle in this case is 86.5 inches. 2nd - spring seat dimension where they're welded, meaning the spring seats are 68.5 inches…
view full answer...To replace the bearings on a Lippert 3,500 lbs axle you will need the outer bearing item #L44649 inner bearing item #L68149. We do have a kit that has the necessary races, seals, and bearings. It is the Hub Bearing Kit for Lippert, Dexter, and Al-Ko…
view full answer...To pick out bearings for a trailer hub you will need to remove one of the hubs so that you can remove the bearings and get the numbers off of them as we don't have a way to look up what a trailer uses based on brand. Or, you can measure the…
view full answer...The Valterra RV Waste Valve, part #T1001B has an inside diameter of 1.9 inches and the outside of the port measures 2.37 inches. I went to our warehouse and measured the waste valve for you. I have attached a photo of the valve with the dimensions…
view full answer...We do offer a 1-1/2 inch spigot that has a flange, it can be found with part #T1006-1. You will want to make sure to secure it with ABS Solvent Bond #A05-0303 which is sold separately.
view full answer...According to the installation instructions from Dexter Axle the torque specs for the wet bolts on their Dexter E-Z Flex Suspension Kits, like part #K71-653-00, is 30 - 50 ft-lbs. I have attached a clip from their instructions for you to check out.
view full answer...For the SCS Frigette Coach 733-0001 the motor replacement you mentioned is correct. For a replacement motor you would want the part #LC301695. You might make sure that the step isn't damaged mechanically too. If the linkage or steps are bent in…
view full answer...We have the bearing kit part #BK3-100 that is designed for Dexter 6k trailer axles like yours. This comes with new bearings and a seal. I attached an install video that shows a trailer hub getting rebuilt for you to check out as well.
view full answer...I spoke with my contact at Dexter regarding the axle on your trailer. This is a 6,000 pound axle that uses inner bearing #25580 and outer bearing #15123. For a complete bearing kit, you can use #BK3-100. This will include the correct inner and outer…
view full answer...You will need to pull off your current hubs to remove the bearings and seal to get the numbers so that we can determine for sure what you would need. But MOST likely the correct kit you would need would be the part #BK3-100. This kit comes with outer…
view full answer...