Customers compare APT6SE to these similar products
Products Featured in this Video
Today we're going to take a look at the Tandem-Axle Trailer Hanger Kit for two inch slipper springs, with the 12 inch long equalizers. Now, this leaf-spring mounting kit will include a 3 3/4 inch tall front hangers, the 3 3/8 inch center hangers, the 5 1/6 inch tall rear hangers, and all your necessary hardware to install it. The equalizers themselves, are 12 inches long. Now, this part will… see more >
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Videos
Help Articles
Expert Answers
For your Tandem 8K axles with 2 inch slipper springs, I recommend the Tandem-Axle Trailer Hanger Kit for 2" Slipper Springs - 12" Long Equalizers #APT6SE. The hangers are to be welded to your trailer frame and the holes on the top of the…
view full answer...You will actually just need kit #APT6SE-36 which is the same thing only the equalizers in it are 13-1/8 inches long. The hardware with each is specific to the kits so some of the other parts are different but for 2 inch slipper springs and 13-1/8…
view full answer...It really depends on the springs used. Take a look at the picture I have included that shows hanger spacing based on several different springs. This will be a good guide to reference when mocking up the suspension on your trailer. This is also found…
view full answer...There isn't a specific distance the hangers have to be for hanger kit #AP216-H238. A good place to start is 30-1/2 inches on center but you would only really know by mocking it up on the trailer before permanently installing the hangers. To…
view full answer...I have another option for you but there is not a screw on spindle available for the #8327872 you were looking at. To replace one of the spindles on the Dexter Trailer Axle Beam with 4" Drop E-Z Lube Spindles - 94" Long - 7,000 lbs #8327872…
view full answer...The #42 E-Z Lube 4" Drop Spindle w/ Flange for 5.2K to 7K Trailer Axles #TRU39FR is the same size as that used on the Dexter Trailer Axle Beam with 4" Drop E-Z Lube Spindles #8327860. Both will fit the same Dexter Trailer Hub and Drum…
view full answer...Appreciate those measurements, and you are 100 percent fine using the Tandem-Axle Trailer Hanger Kit for 2" Slipper Springs - 12" Long Equalizers #APT6SE. The very slight variance between your measurements and the hangers are not going to…
view full answer...I don't have any recommended installers, but any trusted mechanic should be able to complete the installation for you without too much difficulty. If you're moderately handy, you might even be able to complete the install yourself, as the…
view full answer...The slipper spring hook of a slipper spring like part #e67SR attaches to the equalizer and the eye of the spring attaches to the hangers of Tandem-Axle trailer hanger kit part #APT6SE. I have attached a diagram of how slipper springs are setup. I…
view full answer...Trailer spindles should only be installed by a qualified fabricator with trailer axle experience who has the necessary equipment to square up a trailer spindle. It's not a project for someone who's pretty good at welding since if the spindle…
view full answer...We do have options like the #42 E-Z Lube Spindle part #TRU37FR which has the correct 25580 and LM67048 bearing combo that you need. In order to confirm fit you will however still need to confirm the axle tube type (round/square) and diameter (if…
view full answer...Surge brakes use a hydraulic actuator to push fluid to the cylinder piston to activate the brake shoes on drum brakes or brake pads on disc brakes. This pressure should only be applied when weight is pushing against the hitch ball, so no pressure…
view full answer...