Customers compare TLL12RK to these similar products
Products Featured in this Video
Today we're going to be taking a look at the Optronics LED trailer tail light kit. This kit comes with two tail lights, two rubber mounting grommets and two three-prong wiring connectors. The kit is SAE and Department of Transportation compliant. The oval trailer tail lights serve three functions such as your stop light, tail light and turn signal light. Each light is sonically sealed so it has a… see more >
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Videos
Help Articles
Expert Answers
Thank you for the photo of your Coleman trailer's Bargman 92-series tail light. We do offer a replacement Bargman 92-series light assembly, part #30-92-001, which uses the same 1157 bulb as your original. For a bulb only use part #DI79VR. I…
view full answer...Is there a solenoid screwed in to the back of the master cylinder on the trailer? Or is there a lever on the actuator that you move whenever you need to be able to back the trailer up? If so, then you have a reverse lock out. I attached a link to a…
view full answer...The best way to determine the height needed is to measure from the top of your trailer frame to the top of the sides of your boat. If the 40" Tall Guide-Ons #CE27626 sit right at or slightly above the sides of your boat then the shorter will…
view full answer...I pulled one of the units off the shelf in our warehouse and I have copied the directions that are included in the package for you. I called my contact at the manufacturer and the LEDs have a lifetime manufacturer warranty. Instructions: Your light…
view full answer...When it comes to trailer taillights the terms waterproof and submersible are somewhat interchangeable. If a taillight is considered submersible that means that the internal circuits are waterproof and would be protected for if you were to back the…
view full answer...I have a solution for you, but I do not recommend attempting to drill into the spindle to install a zerk fitting. Instead, I recommend using Bearing Buddy Bearing Protectors to help make greasing your trailer axles easier. The Bearing Buddy will…
view full answer...No the LED Trailer Tail Light with Reflector #328-003-6019R does not need a gasket for installation. The light has a sealed, waterproof housing and lens which makes the light submersible. The light is rated up to 100,000 hours of operation. If you…
view full answer...I checked with Command Electronics and they do not offer a replacement lens for the LED Trailer Tail Light part #328-003-6019R because it is a sealed unit therefore your only option is to replace the entire assembly but this will be super easy as it…
view full answer...I wasn't able to find any size info for the Glo Brite trailer light you have, but the part #STL72RB that you referenced is a 6-1/2 inch by 2-1/4 inch LED light assembly that can do stop/turn/tail functions that would work great on nearly every…
view full answer...The Glo-Brite 9553 you have currently measures 6-1/2" x 2-1/4" x 2-1/4" so for an incandescent replacement option I recommend the Custer Trailer Tail Light - Submersible - Stop, Turn, Tail - Incandescent - Oval - Red Lens #G65R which…
view full answer...When our installers replace a trailer hub, there isn't a set torque spec used when tightening the spindle nut. The hub is placed on the spindle, making sure the inner and outer bearings are correctly seated. The spindle nut is then run down until…
view full answer...The 27 inch overall length of the Long Safety Chain, #2118-605-04, includes the hook. I pulled the chain from our warehouse and found that the chain portion measures 25 inches. We do offer longer chains if you are interested. I have attached a link…
view full answer...