Customers compare 8-201-5UC3-EZ to these similar products
Products Featured in this Video
Today, we're going to take a quick look at Dexter Axles, Trailer Hub and Drum Assembly, part number 8-201-5UC3-EZ. This hub and drum assembly is designed to work on 5200-pound axles that use a 2-1/8 or 2-1/4 inside diameter grease seal. It's got a 6 on 5-1/2-inch bolt pattern. We count the studs, we'll get six and if we're to measure across from one stud directly across to another, we get our… see more >
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Videos
Help Articles
Expert Answers
The only differences between the two hubs you mentioned #8-201-9UC3-EZ and #8-201-5UC3-EZ are that the 8-201-5UC3-EZ is not pre-greased and the other is and they have different bearing between the two. But the bearings both have the same inner…
view full answer...Based on the GVWR of your 2019 Jayco North Point 315RLTS it does seem like you have 7k axles. I recommend verifying this information to be sure. These axles typically use the #14125A outer and #25580 inner bearing found in the Timken #TMK92VR.…
view full answer...I can certainly point you in the right direction. This will be a tricky one, as the Dexter 5,200 lb axles can use more than one seal size. We do not have the ability to pull an OEM build sheets to see what parts they installed at the factory so we…
view full answer...You can absolutely upgrade your manual electric trailer brake assemblies on your tandem axle trailer to self-adjusting brakes like the 10 inch #AKEBRK-35-SA or the 12 inch #AKEBRK-7-SA. As long as the assemblies on each axle match you can update your…
view full answer...If it feels like the hubs are getting too hot, one item to check is if the spindle nut is too tight and the added stress on the bearings is overheating the bearings and hub that could cause damage to the bearings. I have attached a video of our…
view full answer...Weight ratings are a little weird when it comes to hub/drum assemblies but as long as the bearings and the inner diameter of the seal (2.250") that comes with the Dexter Trailer Hub and Drum Assembly - 6,000 lb E-Z Lube Axles #K08-201-9B matches…
view full answer...You will not want to use agricultural hubs if you intend to pull the trailer on the highway. Agro hubs are usually speed-limited to 20-mph. Similar speed limitation generally applies to tires intended for use on farm equipment. The keys for selecting…
view full answer...Yes, we had a customer who was able to replace his Dexter 8-155 hubs with the #8-201-5UC3-EZ that you referenced so they should work well for you. You can verify that this hub will work for you by pulling your current hub and making sure they have…
view full answer...In addition to making sure the pilot hole of your wheel is large enough you will also need to measure the bolt pattern of your wheel (see FAQ and video). The bolt pattern of the Dexter Trailer Hub and Drum #8-201-5UC3-EZ is 6 on 5-1/2. I contacted…
view full answer...We've checked in the past and found that the M1102 trailer that you have has a hub that has bearings #14125A and #25580 which matches hubs like the #42866UC3-EZ which has an 8 lug bolt pattern. There isn't a hub that would fit that has the 5…
view full answer...The maximum hub bore measurement for the 5,200 LB or 6,000 LB Dexter hub and drum assembly #8-201-5UC3-EZ is 3.622 inches. So a wheel with center bore of 3-3/4 inches would fit.
view full answer...The complete wet bolt and shackle strap replacement kit I recommend for your application is the MORryde Suspension Upgrade Kit for Tandem Axle Trailers #MR46ZR because it includes the wet bolts with the grease fittings as well as 1/2" thick…
view full answer...