Customers compare BWBMTT31004 to these similar products
Products Featured in this Video
Today, we'll be taking a look at part number BWBMTT31004, this is the B & W triple tow travel mount for 2 inch hitches. The ball mount with the built in hitch balls is going to let you hook up your trailer to your tow vehicle. The shank is going to slide into the receiver tube of your hitch. You'll need to secure it with a hitch pin and clip, or a hitch pin and lock. Those are going to be sold… see more >
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time.
Videos
Help Articles
Expert Answers
The installation of a trailer wiring harness on your 2022 Honda Pilot may seem difficult but it is not as complicated as you would think. The first thing would be deciding on what wiring harness to use, I recommend the T-One Vehicle Wiring Harness…
view full answer...Thanks for that photo, and I checked with Go Power and you will need a solar panel compatible with your Go Power Solar on The Side, from Go Power. I verified with them that the panel you will need to connect to this is the panel you mentioned as it…
view full answer...Yes, you can use the Redarc 200 watt solar panel with your RV that is pre-wired for solar, but you would not be able to use just the Solar Panel #RED86VR. Solar panels require a charge controller to regulate the battery charge so you would need to…
view full answer...The BOLT Trailer Hitch Receiver Lock #BL7023585 is capable of fitting the 3" receiver hitch. I have included the measurements below if you would like to confirm those with your hitch on your 2021 Ford F-350. There are also many reviews on our…
view full answer...I've attached a portion of the instructions for the Dexter Heavy-Duty Suspension Kit for Tandem-Axle Trailers #K71-359-00 that will give your the torque value of 30-50 ft lbs for the hangers, the equalizers, and the shackle straps.
view full answer...I confirmed with my contact at Curt that the spring bars of the Curt Trunnion Weight Distribution System part #17302 is 30-5/8 inches. You are also correct about the Curt Short-Arm Systems as they have 28-5/8 inch length spring bars. I attached an…
view full answer...The L-brackets of the Reese weight distribution system #RE44FR need to install between 24.5 and 27.5 inches from the hitch ball center. I attached a picture that I took from the instructions that shows this. The range gives you a bit of flexibility…
view full answer...From where the B and W hitch part #BWHDRH25198 attaches to the frame of a truck down to the top of the hitch opening measures 7-3/8 inches.
view full answer...I reached out to the manufacturer, Buyers Products, who told me the pre-drilled mounting holes are 1/2" wide x 3/8" tall for their 12 x 18 mud flaps, which are the following part number: - Truck Mud Flaps - Black Rubber - 12" Wide x…
view full answer...I would be happy to recommend a ball mount for your Ram 1500 4WD with air bags installed, but the correct ball mount is really going to come down to how much of a rise/drop you need to tow your trailer level. To determine the rise/drop you need you…
view full answer...You'd need a drop of right at 1 inch to tow the trailer you mentioned level based on the dimensions you listed. The closest to that is a 2 inch drop ball mount like the part #C45331 which fits a 2 inch hitch like you have as well. It has a towing…
view full answer...This will depend on the hitch used and the height of the trailer coupler. You want the trailer to be as level as possible. We have a page on calculating hitch height and coupler height to help you find what ball mount would work best. Most light duty…
view full answer...