Availability of Replacement Hitch Install Hardware # C13046

Question

Question:

I have the Curt 13046 hitch but dont have the hardware kit. Any chance you all sell it separately? 2006 Subaru B9 Tribeca. Many thanks!

asked by: Jerrie C

0

Expert Reply:

We do sell replacement hardware for all of the hitches including the # C13046 we carry with the part # RHK.

expert reply by: Jameson C

0

Answer 1

You can use the Curt #D210 with an adapter, but it will reduce the tongue capacity of your trailer hitch receiver by 50%. If that is acceptable with your combination then I recommend the Malone 2" Dual Purpose Hitch Receiver #MPG544 which will…

view full answer...

Answer 2

To install Curt trailer hitch #C13046 on your 2007 Subaru Tribeca you will only need to temporarily remove the spare tire from under the vehicle. After the hitch is installed, you will put the spare tire back where it was. There is no mention of…

view full answer...

Answer 3

Installation of the CurtTrailer Hitch, item #C13046, does not require modification of the rear bumper or fascia. You will need to temporarily remove your spare tire, then you can replace it after the installation is complete. Some items you may need…

view full answer...

Answer 4

For your 2007 Subaru B9 Tribeca, there is not a confirmed fit for the 1-1/4 inch hitch. Curt does have a 2" fit like you mentioned. The Curt #C13046 is the only hitch available that is confirmed to fit your Tribeca. Because you do not wish to…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 8

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Answer 9

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 10

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 11

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 12

The 7290 that you see is a casting number. It is found on AL-KO hubs that fit #99 spindles. I found that the bearings used are #28580 which would be the inner bearing and #25580 which would be the outer bearing. For the seal use #91030.

view full answer...