Seal With Dimensions to Replace 171255UC

Question

Question:

is a 168255tc and a 171255uc interchangeable

asked by: Mike

0

Expert Reply:

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be # 58846. I've added a link to a video review of this seal for you to take a look at.

expert reply by: Kyle S

0

Charlie

2/26/2024

Will the XLPROLUBE1980SEAL work for a replacement of 171255uc

Reply

Kyle S.

2/27/2024

@Charlie Yes, so long as your axle is a 3,500 lb axle and your hub bore is 1.98" then the # # XLPROLUBE1980KIT will work.

Reply

Answer 1

From what I could find, the #171255UC grease seal has an inner diameter of 1.719 inches and an outer diameter of 2.565 inches. These dimensions match our TruRyde Double Lip Grease Seals, #RG06-050. If possible, I recommend verifying the inner…

view full answer...

Answer 2

On grease seals the TB means a low pressure, double lip seal with a spring and the VB means a non-pressure, single lip seal without a spring. The seal you will need for the part #171255TB is the TruRyde Grease Seals-Double Lip, part #RG06-050. This…

view full answer...

Answer 3

The 171255UC seal has an inner diameter of 1.719" and an outer diameter of 2.565". I was unable to find an oil seal that matches these measurements, but we do have the Grease Seal - Double Lip - ID 1.719" / OD…

view full answer...

Answer 4

For a hub that has the bearing numbers L68149 and L44649 the grease seal you would want is the part #RG06-050.

view full answer...

Answer 5

From what I was able to find out from my research, the Tie Down Engineering 11033 hub has a 5 on 4-1/2" bolt pattern and is designed for 3500-lb axles. Replacement hubs that have these specs typically use a #L68149 inner bearing and #L44649…

view full answer...

Answer 6

I can help you determine what hubs and rotors will work to as replacements on your trailer, but I will need a bit more information. Additionally, it is best to replace the hubs and rotors for both sides of the trailer to know that you are getting the…

view full answer...

Answer 7

The recommended lug nut torque for Loadstar ST215/75D14 Bias Trailer Tire with 14 Inch Galvanized Wheel, #AM3S560, is going to depend on your lug nut size. I have attached a chart which includes the following torque specs: 7/16 inch lug nut, 55-65…

view full answer...

Answer 8

We have just what you are looking for. I called my contact at TDE and asked about the hub you have on your boat trailer. They told me that it was a 5-stud idler hub for a 3,500-lb axle. That means you need the part #AKIHUB-545-35-K. This is a fit for…

view full answer...

Answer 9

If your weight capacity is 3,100 lbs then you probably have a 3,500 lb axle on your trailer. Since your trailer is a boat trailer I recommend going with a galvanized hub like part #AKIHUB-545-35-G-EZ-K for an EZ Lube hub or part #AKIHUB-545-35-G-K…

view full answer...

Answer 10

There typically aren't any part numbers stamped onto the trailer spindle that can be used for identification. There are however numbers stamped onto the hub most times which can be used for identification. The TDE46210 tells me you have a 3,500…

view full answer...

Answer 11

No parts are more critical for the dependable performance of your trailer than the bearings, races, and seals. To ensure that your trailer performs reliably, you should inspect the bearings, races, and seals and repack the bearings every 12 months or…

view full answer...

Answer 12

If the trailer is supposed to have 185/80-13 tires on it, then you should stick with that tire size and use #AM3S334. This is the correct size tire with a galvanized wheel. The only difference is this is a bias tire and not a radial. A bias tire the…

view full answer...

Seal With Dimensions to Replace 171255UC

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching