Lift Kit For Dexter 3,500LB Torflex Axle On a 2020 Forest River Rockwood A122S Hard Sided A-Frame

Question

Question:

I have a 2020 Forest River a122S. I have the lift kit from etrailer and just want to confirm these are a match for my camper. Thank you.

asked by: Jerry S

0

Expert Reply:

Yes, I do see the Torflex Lift Kit # K71-707-01 is the correct part for your 2020 Forest River Rockwood A122S. This camper is supposed to have a 3,500lb Dexter Torflex axle which the lift kit above fits.

expert reply by: Bud M

0

Answer 1

I was able to identify your axle thanks to the tag you sent in and Dexter's help and found that the lift kit you'd need would be the Torflex Lift Kit - Single Axle - 2-5/8" Lift #K71-707-01.

view full answer...

Answer 2

The reducer sleeve does need to be a bit smaller than the interior dimension of the receiver or it could become stuck. Typically a bit of 'slop' between the shank and the receiver or in this case, the reducer and shank isn't much of a…

view full answer...

Answer 3

From what I was able to find with some research it does look like most 2015 Rockwood A122 Pop-up campers had Dexter #9 Torsion axles, but I was not able to verify that with the number you provided. Assuming that your trailer does have the #9 Torsion…

view full answer...

Answer 4

The best and only option we have if your leveling system is too close to the ground is to add a lift to your Forest River Rockwood which will raise it and give you added clearance. You didn't mention the model of your Rockwood but the best option…

view full answer...

Answer 5

It depends on how much clearance you currently have around your wheels. Ideally, you should have 3 inches minimum clearance between your fender and your wheels and an inch minimum between your sidewall and trailer frame/wall. As your wheel size…

view full answer...

Answer 6

I can absolutely confirm the correct lift kit for your trailer. Based on your photos, you do in fact have a #10 Torflex axle, and they are compatible with the lift kits because you do not have 3" high-profile brackets (which just means the…

view full answer...

Answer 7

From what I could find, your 2016 Casita Spirit Deluxe most likely uses a Dexter torsion axle. The Torflex Lift Kit #K71-707-01 is compatible with Dexter #10 Torflex axles which is likely what you have. This lift kit raises your trailer frame by…

view full answer...

Answer 8

The correct lift kit to use on your Forest River R-Pod Trailer will depend on the year. If you have a post 2014 then you will need to use the Axle Riser Kit part #LC382741 for square shaped axles or part #LC270682 for diamond shaped axles as Forest…

view full answer...

Answer 9

Actually the Torflex Lift Kit - Single Axle - 2-5/8" Lift #K71-723-01 will not fit your 1993 Jayco 1206 KB pop-up camper. This lift kit has a weight capacity of 2000 lbs., I checked online and found that your Jayco has a 2440 GVWR. The correct…

view full answer...

Answer 10

The Jayco Jay Feather Lite x17z uses a Dexter Torflex Axle so we do have lift kits available. The correct one is the Torflex Lift Kit part #K71-707-01 for model #10 from 2,300 lbs to 4,000 lbs.

view full answer...

Answer 11

The Dexter Torflex Lift Kit #K71-707-02 referenced in your question is designed for the #10 Torflex axle with a 2,300 to 4,000 pound capacity. As you mentioned, the lift kit cannot be used with Torflex axles that use a 3 inch high profile bracket.…

view full answer...

Answer 12

Increasing the tire and wheel size can increase the height of the trailer but it's usually quite minimal. Before you do anything else you should see if the pin box can be adjusted. Although you have to be careful here since This will lower the…

view full answer...