Availability of Replacement Mounting Hardware for Fulton Fixed Marine Jack # TJ12220301

Question

Question:

Do you sell the bolts and brackets as pictured with this jack separately? If so, kit or part number, price and shipping. Thanks.

asked by: Edward U

0

Expert Reply:

Replacement mounting hardware for Fulton marine jacks is available in a kit consisting of 2 brackets, 4 bolts and 4 nuts. These are available together as part # F500286. A link to this item is provided.

expert reply by: Adam R

0

Answer 1

I will start with the hubs. You have Dexter 8-248 hubs so the correct replacement is the Dexter Trailer Idler Hub Assembly for 3,500-lb Axles - 5 on 4-1/2 #84545BX. This assembly includes the bearings, races and seals. For Bearing Buddy replacements,…

view full answer...

Answer 2

Thanks for sending me your picture; it helped out a lot! Instead of new U-bolts, I would instead suggest the Fulton replacement mounting hardware #F500286. This will be able to accommodate different sized frames of trailers and the threads will be…

view full answer...

Answer 3

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 4

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 5

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

Answer 6

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 7

I have attached a chart you can check out that describes the torque needed per wheel size, wheel stud size and material. For an 8-inch wheel with a 1/2-inch wheel stud the torque is 75 to 86 ft-lbs. For a 15 inch steel wheel with 1/2 inch wheel studs…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

Hey Kevin, for your Demco DA70 actuator you can use the Reverse Lockout Solenoid for Demco Hydraulic Brake Actuators #DM11993.

view full answer...

Answer 10

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 11

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 12

The UFP H-1377 correlates to a Dexter #84 spindle, which is for a 3,500 pound axle. This will utilize an inner bearing #L68149 and an outer bearing #L44649. As this is being used on a boat trailer, I highly suggest going with the etrailer.com…

view full answer...