Width of Draw-Tite 75420 Hitch

Question

Question:

HITCH 75420, WHAT IS THE WIDTH. NEED TO KNOW TO FIT THE FRAME OF THE VEHICLE.

asked by: Scot S

0

Expert Reply:

I have attached a diagram I made of the Draw-Tite Max-Frame Trailer Hitch Receiver item # 75420. From bolt hole to bolt the hitch is 37-5/8". This hitch fits 2004 - 2008 Dodge Ram Pickup 1500s and 2003 - 2009 Dodge Ram Pickup 2500 and 3500s. I have linked an installation video.

I saw you were looking for a hitch for a 2008 Dodge Sprinter Van. There is a Draw-Tite that fits multiple models and wheelbases. It is item # 75549 and it fits:

2500 Van - 144 inch Wheelbase - with standard bumper
2500 Van - 170 inch Wheelbase - with standard bumper
3500 Van - 144 inch Wheelbase - with standard bumper
3500 Van - 170 inch Wheelbase - with standard bumper

expert reply by: Jerred H

0

Draw-Tite 75420 Width
(click to enlarge)

Answer 1

The Buyers Products Flatbed/Flatbed Dump Hitch Plate Bumper with 2" Receiver #3371809055 you were looking at measures 34-1/2" between the sides of the hitch which you can see in the included diagram. This hitch may fit with your Tommy Lift,…

view full answer...

Answer 2

We have many hitch options for a truck that has a lift gate, but very few of them are a simple bolt on custom application. Because the locations for attaching lift gates vary, you will need to use a weld on option like the Class V Universal Weld-on…

view full answer...

Answer 3

In order to choose the best weight distribution hitch, you will first need to know your total tongue weight (TW), which is the tongue weight of your fully loaded and ready to go trailer plus the weight of any cargo behind the rear axle of your tow…

view full answer...

Answer 4

There are traditional and standard wiring configurations and that can be frustrating when working with electrical connectors. We try to always remind customers to check wiring for function and not to rely on the color of the wires for that reason.…

view full answer...

Answer 5

You can install a 7 way connector on your 2019 Ford F-150 by using the Curt T-Connector #C56413, which will plug into the factory supplied 4 way connector plug on your vehicle and give you a fully functioning 7 way connector. If you've got a…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...

Answer 9

Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…

view full answer...

Answer 10

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 11

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Answer 12

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...