Trailer Hitch Compatible with Liftgate Truck

Question

Question:

wondering if you carry a trailer hitch that will work with a liftgate?

asked by: Kurt M

0

Expert Reply:

We have many hitch options for a truck that has a lift gate, but very few of them are a simple bolt on custom application. Because the locations for attaching lift gates vary, you will need to use a weld on option like the Class V Universal Weld-on Receiver Hitch # 15903. There are many different bracket options for a hitch like # 4907 and # 4916.

expert reply by: Jason S

0

Answer 1

None of the custom fit hitches we carry are going to have a distance of 10 inches or less from the rear mounting hole to the hitch opening. Your best option is going to be a multi-fit hitches like the #41990 that has a 16k capacity. This is a weld…

view full answer...

Answer 2

According to B&W the B&W Turnoverball Underbed Gooseneck Trailer Hitch w/ Custom Installation Kit part #BWGNRK1020 is about a 2 hour install by a professional. All the Hardware is provided. I have attached the installation…

view full answer...

Answer 3

I do have an option for you but there aren't any direct wiring adapters to go from a 4-round to a 7-blade. Therefore, you'll need to remove the 4-round and install a 7-blade which is really your best option since this is far more…

view full answer...

Answer 4

A trailer hitch may cause some interference with the hands-free liftgate on your wife's 2018 Toyota RAV4 because it is partially in front of the motion sensor, but it will still work as normal. For example, the etrailer #e98864 will allow full…

view full answer...

Answer 5

I may have another option for you, but the Curt Trailer Hitch Receiver - Custom Fit - Class IV - 2" #c14006 you mentioned is only confirmed to fit select 2014-2019 GMC/Chevrolet 1500 trucks and will not fit your 2006 Chevrolet W-3500 or 2006…

view full answer...

Answer 6

I attached a picture that shows what the typical dual tank setup looks like with the accessories needed labeled. First thing you need is pig tails to go from the tanks to the regulator like the part #100473-12. Then for a dual tank regulator with…

view full answer...

Answer 7

The best option we have available for your 2008 Sterling Bullet Cab and Chassis is the Draw-Tite Ultra Frame Service Body Trailer Hitch #41991 paired with the 16" Weld-On Bracket Kit #4916. These extra long brackets will give you the drop needed…

view full answer...

Answer 8

The MaxxTow Hitch Extender with Step, part #MT70069 is a hollow hitch extender. I've attached a video where they mount a High/low adapter through the extender and its shank is roughly the same length as the useable part of the hitch extender…

view full answer...

Answer 9

What Gen-Y said is correct, and this is the best solution for a problem like yours. The Replacement Shank for Gen-Y Adjustable Ball Mount - 2" Hitch - 7-1/2" Drop/Rise - 16K #325-GH-504 will not reduce your tongue weight capacity at all. It…

view full answer...

Answer 10

The short answer to both of your questions is yes. You can remove the backing plate or brake assembly and use the existing hub with integrated drum by itself, or, you can simply replace it with an idler hub. Based on the photos, I would suggest…

view full answer...

Answer 11

Your best option is either going to be going with a Curt hitch, #15902, or going with one of the hitches with 16 inch brackets like #41990-16. This hitch is closest to what you need. You will need to have a qualified professional welder perform the…

view full answer...

Answer 12

Typically the solution for your 2019 E-450 Cutaway is a universal hitch like the Curt #15903 you looked at. With the liftgate you will have to figure out if it will fit or not based on the placement and design of the liftgate. Some have too many…

view full answer...

Trailer Hitch Compatible with Liftgate Truck

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching