Using 2" Attachments with a New 2-1/2" Receiver

Question

Question:

Thank you for the answer to my question. You are very helpful. The only thing I can't find is a weight limit on the B&W 2 and 1/2-in to 2-in reducer?

asked by: Gary H

0

Expert Reply:

It sounds like you have some older 2" accessories that you need to work with your new 2-1/2" receiver. We have you covered.

One option you have is to simply use a reducer sleeve like the B&W Hitch Receiver Reducer Sleeve, part # BWRHXA2182. This will slide into your 2-1/2" receiver and allow you to use your 2" attachments. I've linked to a video demonstration of this.

Another option is to replace some of the smaller parts so you don't need a sleeve. For your weight distribution system's shank, we have the Equal-i-zer Weight Dist Shank - 2-1/2" Hitch - 7" Rise, 3" Drop, part # EQ90-02-4700. Since shanks are basically interchangeable between different weight distribution systems, this will work perfect for you (provided the drop and rise fit within your requirements, of course). I've linked to a video review of this shank for you to look at.

As for a dedicated ball mount, I've linked to a list of our 2-1/2" ball mounts below. The only thing you will need is to find which rise or drop you need.

expert reply by: Kef G

0

Gary H.

1/27/2021

Thank you for the answer to my question. You are very helpful. The only thing I can't find is a weight limit on the B&W 2 and 1/2-in to 2-in reducer?

Reply

Kef G.

1/27/2021

Reducer sleeves like the B&W one, part # BWRHXA2182, typically do not have a weight rating. This may seem strange as many hitch reducers do have weight ratings, but those are the ones that extend out past the receiver (thereby giving additional length/clearance). The lower weight rating for these is mostly there because of the extension, not so much the build-quality of the reducer. In other words, the further out from your hitch, the lower the capacity it can handle. A sleeve, on the other hand, does not extend past the receiver. It simply fills the space so the 2" accessories fit snugly in a 2-1/2" receiver. For this reason, the towing capacity of your hitch will not change when using the sleeve.

Reply

Answer 1

The short answer to this question is- No. The B&W Hitch Receiver Reducer Sleeve #BWRHXA2182 does not reduce the tongue weight or towing capacity of your hitch in the same manner that a hitch adapter like the #HTAD would. You will still be able to…

view full answer...

Answer 2

As your 24' Legend 12,000lb aluminum equipment trailer has torsion axles there is nothing that can be added to these to improve the bouncing that you have. Being that your trailer is constructed of lightweight materials and has such heavy duty…

view full answer...

Answer 3

We do offer a reducer that will allow you to use a Class III or IV accessory in a Class IV 2-1/2 inch receiver. The Curt Reducer Sleeve, part #C45405 would work well for you. The outside dimension is just a bit less than 2-1/2 inches, to allow for…

view full answer...

Answer 4

I would be happy to help! Both the Draw-Tite Class V Trailer Hitch Receiver #DT45508 and the B&W Class V Trailer Hitch Receiver #BWHDRH25230 you were looking at for your 2004 Ford F-250/350 King Ranch will stick out from the bumper slightly like…

view full answer...

Answer 5

That's a very cool bike so I can see why you want to bring it but the issue is that any type of extension is going to reduce your tongue weight capacity by 50 percent which is not something you will be able to do. The only thing you can do to add…

view full answer...

Answer 6

The ground clearance difference between Fastway round bar and trunnion bar weight distribution systems is about an inch at the head so it isn't much at all. And since you need to have it set up in the rise position you could go either way and…

view full answer...

Answer 7

Since you have an aluminum trailer I suggest using a tie-down that has a backing plate like #RR5K. This will help reinforce the tie-down since aluminum may not hold up. It would be even better if you can install the tie-downs to the frame of the…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...