Difference Between Trailer Hitches for 2004 Pontiac Vibe and Pontiac Vibe GT

Question

Question:

pontiac vibe gt and base model whats the differance between the two when it comes to the hitch

asked by: Buddy

0

Expert Reply:

The only difference is that Curt has one trailer hitch that fits a 2004 Pontiac Vibe GT, part # C12221 and one trailer hitch for a 2004 Pontiac Vibe NON-GT, part # C12234 while the Draw-Tite # 24812 will fit both models.

The Draw-Tite hitch is a Class I hitch which requires the use of Class I accessories so my recommendation is to go with the option from Curt, with the right hitch depending on if you have a GT or not.

Both the Curt Trailer Hitch # C12221 (GT models) and # C12234 (non-GT models) will fit a 2004 Pontiac Vibe and each are Class II hitches, giving you more - and better - options for accessories than a Class I hitch. The only difference in capacites is that the # C12221 has a 2,500 lb towing and 250 lb tongue weight capacity compared to the 2,000 lb towing and 200 lb tongue weight capacity of the # C12234.

If you want these hitches to tow a small trailer, the correct ball mount for both trailer hitches is the Curt # C45521 which does not come with a pin; for that you would need part # F-4. For a hitch ball, the correct one will depend on the size of your trailer's coupler. You will need either 1-7/8" Hitch Ball # A-80 or 2" Hitch Ball # A-82. Then for wiring to add power to your trailer's lights I recommend the T-One Wiring Harness # 118458.

I have added links to video installs of the harness as well as both hitches on a Pontiac Vibe for you to check out.

expert reply by: Kyle S

0

Answer 1

Curt trailer hitch #C12221 would be a good option as long as your 2005 Toyota Matrix is not an XR or XRS model. If it is an XR or XRS model then #C12013 would be the best option for a Curt hitch. These are both Class II hitches which means you have…

view full answer...

Answer 2

All available hitches made for your 2007 Toyota Matrix XR include both Class I and Class II types in the 1-1/4-inch size. All are shown on the linked page. You'll notice all three options, parts # 24812, #C12221 and #C12013, share a very similar…

view full answer...

Answer 3

Hitch manufacturers determine the Class rating for a given hitch. The amount of hardware used to install a hitch isn't a factor. With that said Curt decided that hitch #C12234 will be fine to use with Class II accessories and gave it a Class II…

view full answer...

Answer 4

The only note in the actual instructions for Curt Trailer Hitch, #12234, are for a different vehicle on which this hitch also fits. However, we have found that it is possible that the heat shield in question will need to be trimmed using aviator…

view full answer...

Answer 5

There are 2 possible trailer wiring options for your 2005 Pontiac Vibe GT. The Tow Ready Custom Fit Vehicle Wiring, #118458, that you have referenced would be the easiest to install. It has 3 sets of connectors and a ground wire. The 3 sets of…

view full answer...

Answer 6

Curt's 1-1/4-inch Class II round tube hitch #C12013 is a confirmed fit on the AWD 2005 Toyota Matrix XR and XRS and offers no-drill installation. The hitch will bolt to the bottom of the car's frame rails using the included hardware. Heat…

view full answer...

Answer 7

The Tow Ready Custom Fit Vehicle Wiring, #118458, does not require a direct connection to the battery when installing and can be used on your 2003 Pontiac Vibe GT. However, the benefit of a system that does include a direct connection to the battery,…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

Yep, so long as your 2024 Subaru Crosstrek Wilderness is not a hybrid both the Curt and etrailer hitches will fit: - Curt Trailer Hitch Receiver #C13382 - etrailer Trailer Hitch Receiver #e98912 The only difference besides price is the finish; the…

view full answer...