Trailer Hitch Fit for 2007 Toyota Matrix XR
Question:
I have a 2007 toyota matrix xr. How extensively would I need to trim the rear plastic to get a Curt 12221 in there? I need to get as much ground clearance as possible.
asked by: Reece
Expert Reply:
All available hitches made for your 2007 Toyota Matrix XR include both Class I and Class II types in the 1-1/4-inch size. All are shown on the linked page. You'll notice all three options, parts # 24812, # C12221 and # C12013, share a very similar overall design; this is due to all of them using the same mounting points on the car's frame. This means that there will not be much if any difference between the installations. Ground clearance will not be markedly better or worse with any hitch.
If your intended use is a hitch-mount bike rack then I urge you to select one of the Class II hitches from Curt since these will allow you to carry more bikes than the Class I hitch option which limits you to 2 bikes regardless of the carrier capacity. Do note you need to use stabilizing strap # 18050 with either Curt hitch in order to maintain your hitch warranty.
Products Referenced in This Question
Curt Cam Buckle Stabilizing Strap for Hitch-Mounted Accessories - 61" x 1" - Qty 1
- Accessories and Parts
- Hitch Bike Racks
- Hitch Cargo Carrier
- Tie Down Straps
- CURT
more information >
Draw-Tite Sportframe Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Trailer Hitch
- Custom Fit Hitch
- Class I
- 200 lbs TW
- 2000 lbs GTW
- 1-1/4 Inch Hitch
- Visible Cross Tube
- Draw-Tite
more information >
Curt Trailer Hitch Receiver - Custom Fit - Class II - 1-1/4"
- Trailer Hitch
- Custom Fit Hitch
- Class II
- 250 lbs TW
- 2500 lbs GTW
- 1-1/4 Inch Hitch
- Visible Cross Tube
- CURT
more information >
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class II - 1-1/4"
- Trailer Hitch
- Custom Fit Hitch
- Class II
- 250 lbs TW
- 2500 lbs GTW
- 1-1/4 Inch Hitch
- Visible Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Trailer Hitch
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class II - 1-1/4"
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class II - 1-1/4"
- Shop: Draw-Tite Sportframe Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class II - 1-1/4"
- Q&A: Trailer Hitch and Wiring for a 2005 Toyota Matrix
- Q&A: Difference Between Trailer Hitches for 2004 Pontiac Vibe and Pontiac Vibe GT
- Shop: Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Shop: Tekonsha Primus IQ Trailer Brake Controller - 1 to 3 Axles - Proportional
- Shop: Draw-Tite Ball Mount w/ 2" Ball for 2" Hitches - 3/4" Rise, 2" Drop - 7,500 lbs
- Video: Trailer Hitch Installation - 2009 Toyota Matrix
- Shop: Floor Mats
- Shop: Brake Controller
- Shop: Trailer Wiring
- Search Results: trailer hitch ball
- Q&A: Installation of Curt Class II Hitch C12013 on 2005 Toyota Matrix XR
- Q&A: Hitch Installation on 2008 Toyota Matrix XR
- Q&A: Differences Between the Curt Hitches for the 2009 Toyota Matrix
- Article: How to Clean Weld Nuts for the Installation of a Trailer Hitch | etrailer.com
- Q&A: Recommended Trailer Hitch for a 2005 Toyota Matrix XR
- Q&A: Replacement Hitch Bolt for Yakima HoldUp 1-1/4 Inch Bike Rack # Y02445
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Video: Choosing the Right Trailer Wiring
- Search Results: 44649
- Article: How to Choose the Right Trailer Hitch Class
- Search Results: 68149
- Video: Choosing the Right Brake Controller
- Search Results: 25580
- Shop: Fifth Wheel Hitch
- Article: Trailer Wiring Diagrams