Is Drilling Required to Install Trailer Hitch on 1991 Chevy Camaro

Question

Question:

Wanted to know if drilling is required when installing this hitch on a 1991 Chevrolet Camaro RS. 5.0L TBI V8

asked by: Mike

0

Expert Reply:

The Curt Trailer Hitch # C11117 will require drilling to install on a 1991 Chevy Camaro. There are two holes that need to be drilled with a 9/16" drill bit in order to secure the hitch.

Please keep in mind that this hitch does NOT fit models with twin tailpipes or single exhaust models that have the bumper with two cutouts for the exhaust.

I have added a link to the installation instructions for you to check out as well.

expert reply by: Kyle S

0

click to enlarge

Answer 1

If you do not have the Turbo and Dual Exhaust models I would go with the Curt Trailer Hitch Receiver #C11282 mainly because according to our website the install difficulty is easier on this one than the Curt Trailer Hitch Receiver #C11282. They…

view full answer...

Answer 2

Yes, the cross tube of the Curt Hitch part #C11282 that you referenced will be hidden when installed on a Verano like your 2015 Buick Verano. Check out the picture I attached that shows this hitch installed on a Verano similar to yours.

view full answer...

Answer 3

The Curt #C11117 will fit your 1987 Chevrolet Camaro with cross-flow muffler with dual exhaust outlets. I double checked with Curt and when they test fit the hitch on this Camaro generation it actually had a cross-flow muffler with dual exhaust…

view full answer...

Answer 4

I spoke to my contact at Curt Manufacturing and they stated that as long as the dual exhaust you have on your 1984 Pontiac Firebird was installed from the factory, then yes the Curt Trailer Hitch Receiver part #C11117 will work for you. However, if…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 8

To add a hitch to your 2024 Toyota RAV4, I recommend the etrailer item #e23ZR. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a 4,000 lbs towing capacity, and a 600…

view full answer...

Answer 9

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 10

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 11

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 12

As far as wiring for the 2024 Toyota Grand Highlander, we do have the Curt #C59236 available which is more of a universal hardwire harness. Unfortunately there are not any plug-and-play options that have been confirmed to fit as of yet (October 4,…

view full answer...