Custom Wiring Adapter for Hayes Brake Controllers - Dual Plug

See what our Experts say about this Hayes Accessories and Parts

• Best Brake Controller for 2018 Chrysler Pacifica with Factory Towing Package
  When installing a brake controller on your 2018 Chrysler Pacifica there are easy and straight forward installation kits available. I see you were looking at the Hayes products. The Hayes-Lemmerz Energize III+ Electric Trailer Brake Controller -Part # HA81742B along with the Custom Wiring Adapter for Hayes Brake Controllers - Dual Plug Part # HA81796-HBC will plug directly in to a port under your dash and allow you to install your controller with little hassle. As an alternative I really...
  view full answer...
• Installing an Electric Trailer Brake Controller in a 2018 Chrysler Pacifica
  Since you already have a 7-way trailer connector and a brake controller all you should need is the adapter to connect the controller. That's assuming the 7-way is factory installed. If you've installed it yourself, or had it installed aftermarket let me know. If it's a factory 7-way there's going to be a connector under the dash above the steering column not far from where it goes through the firewall. The connector you're looking for probably has a green cover over it. Once you find...
  view full answer...
• Brake Controller Fit and Compatibility for a 2016 Jeep Grand Cherokee with Factory 7-Way
  Yes the Hayes Blackbird Brake Controller HA81726 will work for your 2016 Jeep Grand Cherokee, but you will need to use the adapter # HA81796-HBC to plug into your vehicles wiring. Can I offer one bit of advice? Instead of going with a Time Delayed Brake Controller I would instead suggest a Proportional Controller like the P2 # 90885 with adapter # 3045-P. The P2 is a proportional brake controller which means it senses how the tow vehicle is slowing or stopping and applies the trailer's...
  view full answer...
• Brake Controller Harness for Hayes Brake Controller Install on 2016 Ram 1500
  We've got what you're looking for. You'll need the # HA81795-HBC harness. One end plugs into the pigtail exiting the rear of your Hayes 81770 Endeavor brake controller, the other plugs into the factory brake controller connector. The connector is located under the dash, just above where the driver's right knee would be as shown in the provided photo. I'll link to an install video that you might find helpful. The video shows a different brake controller being installed on a 2016 Ram 1500,...
  view full answer...
  
• Recommended Custom Wiring Adapter For Hayes Energize lll Brake Controller On 2008 Lincoln Navigator
  The Custom Wiring Adapter for your Hayes Energize lll Brake Controller and your 2008 Navigator is part # HA81783-HBC. The # HA81796-HBC you referenced is not a fit for the Navigator.
  view full answer...
• How to Remove Brake Controller Wiring Harness from 2015 Jeep Grand Cherokee
  On the gray plug of the # HA81796-HBC that inserts into the connector, there is a locking tab that needs to be pressed in to unlock. I've highlighted that tab in the photo I've edited for you. Keep in mind, depending on how your 2018 Grand Cherokee left the factory, you might need to get the computer flashed at the dealer in order for the controller to work correctly once installed. I've linked you to an install video showing a brake controller being installed on a 2018 Grand Cherokee,
  view full answer...
  
• Installing Brake Controller in 2018 Chevy Colorado
  On this page if you there is a heading titled "Featured Help Information" (most likely have to scroll down below part links), that will have the install video for a brake controller in a 2018 Chevy Colorado that I mentioned in the answer page you found. Your 2018 Chevy Colorado has the brake controller wiring ran under the dash of the truck but there isn't an adapter that uses a connector. Reason being there's only 4 blunt cut wires under your vehicle dash for the brake controller wiring...
  view full answer...
• How Does Brake Controller Install in 2018 Chevy Colorado
  Your 2018 Chevy Colorado has the brake controller wiring ran under the dash of the truck but there isn't an adapter that uses a connector. Reason being there's only 4 blunt cut wires under your vehicle dash for the brake controller wiring and not a connector of any type. To install the Hayes controller part # HA81760 you need the Hayes universal connector part # HA81789-HBC to run to those wires. I attached an install video that shows a similar brake controller installed in a 2018 Chevy...
  view full answer...
• What is the Correct Harness for a Hayes Blackbird Brake Controller on a 2014 Jeep Grand Cherokee
  For the Blackbird brake controller and your 2014 Jeep Grand Cherokee you will need Hayes harness # HA81796-HBC.
  view full answer...
• Hayes G2 Brake Boss Trailer Brake Controller Recommendation for a 2011 Jeep Grand Cherokee
  Yes, you can install the Hayes G2 Brake Boss Trailer Brake Controller w/ Mounting Sleeve # HA81792BB in your 2011 Jeep Grand Cherokee. The connector should be mounted on top of the emergency brake bracket, it's gray in color. Once you find it all you need to do to install this controller is plug the Custom Wiring Adapter for Hayes Brake Controllers # HA81796-HBC into the port under your dash and then plug the other end into the # HA81792BB, mount it, and you'd be good to go.
  view full answer...

Do you have a question about this Accessories and Part?