Availability of 10 Bunk Boards

Question

Question:

Can I get this product in 10 foot lengths?

asked by: Rodney F

0

Expert Reply:

If you are needing 10' lengths then you may be better off using 2 of the 5' long boards, part # CE27820.

The longest bunk boards that we have are found as part # CE27845 and are 7' long so 2 of the 5' boards is the best solution.

expert reply by: Jon G

0

Answer 1

You certainly could make your own bunk boards using pressure treated lumber and bunk carpet like #CE11372 if you wish. CE Smith doesn't use pressure treated lumber in their bunk boards because some of the chemicals used to pressure treat the…

view full answer...

Answer 2

The longest bunk boards we offer pre-wrapped are the CE Smith Carpeted Bunk Boards for Boat Trailers part #CE27845 which measure 7' long. For longer boats, you'd simply install multiple bunk boards on the same side until you have the desired…

view full answer...

Answer 3

The Kenda S-Trail ST145R12 Radial Trailer Tire with 12" Aluminum Wheel - 5 on 4-1/2 - Load Range D #AM31202 referenced in your question is a great radial tire that has a maximum load of 1,220 pounds at 65 psi. The aluminum wheel features a 5 on…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 6

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 9

The three most common lug stud sizes for a trailer are 1/2"-20, 9/16"-18, and 5/8"-18. In order to make sure you get the correct lug nuts you need to measure the lug studs on the trailer now as we have no way to look this up for…

view full answer...

Answer 10

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 11

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...