Availability of a Pipe Mount Trailer Jack with Caster Wheel
Question:
I need a pipe mount jack with the option of a caster wheel.
asked by: Lou
Expert Reply:
I have a couple of jacks that I can recommend for you, but at this time we do not have a pipe mount jack available with the option of a caster wheel.
The first and best fit would be the Bulldog Rack-and-Gear Jack with Steel Wheel - Weld On/ Bolt On - 16 inch Lift - 750 lbs, item # BD162300, which has a angle mounting plate that is 3-1/2 inches tall by 1-3/4 inches wide. If the fact that this jack does not swivel up out of the way is acceptable, it would be your best bet.
The second is the Fulton F2 Swing-Up Trailer Jack, Dual 7 inch Wheels, Sidewind, Weld-On - 1,600 lbs, item # F1413060334, the mounting bracket on this jack is larger, at 5-3/4 inches wide by 4-3/4 iches tall and you would have to do some creative welding to secure it to the trailer frame, which would not look so good in the end, most likely. This is the closest size swivel jack that I have that might work for your trailer.
Products Referenced in This Question
Fulton F2 Swing-Up Trailer Jack, Dual 7" Wheels, Sidewind, Weld-On - 1,600 lbs
- Trailer Jack
- Boat Trailer
- Car Hauler
- Enclosed Trailer
- Utility Trailer
- Leveling Jacks
- Tongue Jacks
- Alloy Aluminum
- 1001 - 2000 lbs
- Sidewind Jack
- Swivel Jack
- 10 Inch Lift
- Weld-On
- With Wheel
- Fulton
more information >
Product Page this Question was Asked From
Pro Series Round, Pipe-Mount Swivel Jack w/ Footplate - Sidewind - 10" Lift - 5,000 lbs
- Trailer Jack
- Car Hauler
- Enclosed Trailer
- Utility Trailer
- Leveling Jacks
- Tongue Jacks
- Steel
- 4001 - 5000 lbs
- Sidewind Jack
- Swivel Jack
- 10 Inch Lift
- Pipe Mount
- Weld-On
- With Rectangle Foot
- Pro Series
more information >
Continue Researching
- Video: Review of Dutton-Lainson Trailer Jack - Sidewind Pipe Mount Swivel Style With Foot - DL22685
- Shop: Bulldog Round Jack without mount - Sidewind - 10" Lift - 2,000 lbs
- Video: Pro Series Trailer Jack - Side Frame Mount Jack - PS1401420303 Review
- Video: Review of Bulldog Trailer Jack - Side Frame Mount Jack - 150010
- Video: Bulldog Trailer Jack - Side Frame Mount Jack - BD195351 Review
- Shop: Pro Series Round, Pipe-Mount Swivel Jack w/ Footplate - Sidewind - 10" Lift - 5,000 lbs
- Shop: etrailer Boat Trailer Jack w/ Wheel - Sidewind - Swivel - 11" Lift - Zinc - 1.5K
- Shop: Pipe Mount Swivel Style Trailer Jack with Foot - Sidewind - 10" Travel - 2,000 lbs.
- Shop: etrailer Boat Trailer Jack w/ 2 Wheels - Sidewind - Swivel - 10-3/8" Lift - Zinc - 1.5K
- Shop: Bulldog Square Jack with Footplate - Fixed Leg - Sidewind - 10" Lift - 3,000 lbs
- Shop: Bulldog Round, A-Frame Jack Drop Leg and Pull Pin Assembly
- Search Results: hitch locks
- Q&A: Spare Tire Carrier and Jack Recommendations for a Load Rite Single Axle Boat Trailer
- Q&A: Jack Options for 2 x 2 Trailer Frame on Kwik Kamper Pop Up Camper with Storage Box on Front
- Q&A: Removing Caster of Bulldog Rack-and-Gear Jack # BD162300
- Search Results: mounting hardware
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Shop: Trailer Hitch
- Search Results: 25580
- Article: Trailer Wiring Diagrams
- Q&A: Availability Of 33" Ark Stabilizer Jack And Dimensional Diagrams Of Similar Ark Corner Steadies
- Article: Most Popular Wheel Bearings
- Search Results: trailer jack
- Video: Timbren Axle-Less Trailer Suspension System Installation
- Shop: Trailer Wiring
- Q&A: What is the Difference Between Load Range C and D ST175/80D13 Trailer Tires
- Video: etrailer Landing Gear Set Review
- Search Results: safety chains
- Shop: Brake Controller
- Article: Trailer Tire Sizing
on Trailer Jack
Steve G.
7/13/2020
Your Bulldog Round Pipe-Mount Swivel Jack with pin attachable wheel should do what I need. Two are required. My Norwood sawmill with integral trailer has six swivel jacks for adjustable level support at log sawing site. My tractor tows this trailer in and out of a fairly large storage garage with smooth concrete floor. When I back the trailer (portable bandsaw sawmill) into the garage, I want to remove the front two plate bottom jacks from their 2 1/2" female mounts and substitute your castor fitted swivel jacks. After I disconnect the trailer from the tractor, I can push the trailer into the best storage location by hand. Your two jacks at the tongue end of trailer will work with the trailer wheels to make a balanced and mobile rig for indoor parking. Can we do this? Ideally, there are 11 to 12 inches below the female side supports for the jacks to the floor when the trailer is level.