Parts Needed to Install a 7-Way Trailer Connector on 2006 Jeep Grand Cherokee Limited

Question

Question:

I have a 2006 Jeep Grand Cherokee limited. It did not come with a factory tow package. I need a 7 way wiring kit for it. Do you have this product? I only see the 4-way kit for my specific vehicle. Thank You

asked by: Matthew H

0

Expert Reply:

If your 2006 Jeep Grand Cherokee Limited did not have a factory trailer package you'll need to start off with a basic 4-pole wiring harness and then add the 7-way. Once you have a 7-way installed this connector will be able to carry trailer brake, tail and turn light functions as well as carry 12V auxiliary power, trailer brake power and reverse light signals - once those additional connections are made.

The 4-pole harness I suggest for your vehicle is the Tow Ready # 118394 which is a plug-and-play type that requires NO cutting or splicing of wires.

With this in place you can add 7-way socket # 37185 to convert the format from the 4-pole flat type to the 7-way RV-style. With adapter part # 37185 plugged in to the 4-pole this dual connector socket will let you connect either a 4-pole or a 7-way trailer plug which gives you the flexibility to tow both types of trailers.

With these two items installed you will have only trailer lighting signals on the 7-way. If that is all you need - meaning no trailer brakes, no 12V trailer power feed and no reverse lights - then you're all set.

If you intend to make those additional circuit connections then instead of part 37185 you'll need our brake controller install kit # ETBC7. This kit will enable you to make the connections for the lighting functions and both brake and 12V power signals to your trailer. The brake controller I recommend is the Prodigy P2 # 90885 which is among the most popular, versatile and reliable units offered. I have linked an article and video showing installation of this kit and the P2 brake controller.

If you have any other questions, please let us know.

expert reply by: Adam R

0

Answer 1

If you had the 7-way wiring connector on your 2006 Jeep Grand Cherokee to install the wiring harness part #20135 the connector would be under the rear of the vehicle near the rear bumper. It would be a square connector typically found right behind…

view full answer...

Answer 2

Trailer wiring harnesses like the Curt #C55381 that have a T-connector allow for quick plug-in installation at the rear of the vehicle. This harness connects to wiring located under the vehicle, behind the bumper on the drivers side. The harness will…

view full answer...

Answer 3

On a trailer the brake lights and turn signals operate on the same wire/bulb. So, it is odd when the turn signals work, but the brake lights don't. There are 3 possible causes for this that are more likely than any of the other possible causes.…

view full answer...

Answer 4

The wiring for all models of the 2006 Grand Cherokee is that same as long as you don't have the tow package. For your SRT8 I recommend the Hopkins, part #HM42545. It plugs in behind the tail lights and then there's a hot lead that needs to be…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 10

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 11

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 12

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...