Double RV Waste Valves - Elbow - Rotating - 3" and 1.5" Hubs to 3" Lug

See what our Experts say about this Valterra RV Waste Valves

• Replacement for Bristol Dual RV Waste Valves V93B15
  Yes, the Double RV Waste Valves part # T80 is exactly what you need to replace the Bristol RV Waste Valves V93B15 that you have now. If you want to reuse your existing spigot flange then they will match up to those on the above as the four bolt flange has the same pattern. This will be a direct bolt-on swap for your trailer.
  view full answer...
  
• Can A Single Gate Valve Be Replaced Or Does The Whole Assembly Have To Be Replaced
  Each gate valve is held in place by four bolts that you can just unscrew and then swap the gate valve out with a new one like Valterra's Bladex # T1003VP and bolt back in place. If your gray gate valve ever needs to be replaced you can use part # T1001VPM. This method means no cutting and gluing in extra fittings for just a simple valve replacement. I've attached a video where I show you exactly how to do this.
  view full answer...
• How to Improve Access to Black and Gray Water Drain Valve
  Thank you for the photo of the black/grey water drain valve on your Forest River Salem 31QBTS travel trailer. I see what you mean about this being well under the trailer and not located for convenient access. Sometimes the presence of slide out mechanisms or other RV features can limit the placement options for the waste valve. RV makers might choose to keep the drain well under the trailer to avoid a nasty problem were it to leak while you're driving. (Consider what would happen if a...
  view full answer...
  
• Recommended Replacement For A LaSalle Bristol V93B1 RV Sewer Fitting
  Thank you for the pictures of your LaSalle Bristol V93B1, it made it a lot easier to find the correct replacement to get your RV's sewer system back in working order. The V93B1 appears to just be the actual drain pipe with the gray dumping into the black line and doesn't include any valves. You'll need the Valterra RV Sewer Heel Inlet # T1030. This is going to have the same 2" hub fitting and 3" rotating flange as your V93B1 so you can easily swap it out. You'll need some ABS Cement #...
  view full answer...
  
• Difference Between Hub and Spigot for Valterra Double Waste Valves
  Yes, the info you listed is correct for the Valterra double waste valves. Part # T80 has a 3" Hub (female) and a 1-1/2" Hub (male) Part # T80C has a 3" Hub (female) and a 1-1/2" Spigot (male) Part # T80A has a 3" Spigot (male) and a 1-1/2" Hub (female) Spigots fit into hubs.
  view full answer...
• Replacement 1-1/2 Inch Hub and Valve for Valterra T80 Double RV Waste Valve Elbow
  The Double RV Waste Valves - Elbow - Rotating - 3" and 1.5" Hubs to 3" Lug # T80 will use the Valterra RV Sewer Spigot with Flange - 1-1/2" # T1005-1 to match the original hub. This secures to your pipe with solvent # A05-0303. The Valterra RV Sewer hub # T1006-1 will also fit but is designed to fit differently than the T80 original connection so it can be a replacement part as well. I've attached a video to help with the dimensions and a couple photos to further assist with dimensions...
  view full answer...
  
• Sewer Elbow Compatible With Item # T80 For A 2018 Jayco 232RB Travel Trailer
  The correct elbow to add the Double RV Waste Valves Item # T80 to your 2018 Jayco 232RB Travel Trailer is Item # D50-2882. I have also include a link to the page for the 1-1/2" elbows incase you needed one for the grey water side.
  view full answer...
• Can the Ends of the Double RV Waste Valves # T80 be Removed
  You could remove the ends of the Double RV Waste Valves # T80 but instead of purchasing this part I recommend using the RV Sewer Elbow # T1036 which is what I believe you are trying to use. If you are needing to replace any of the valves we have those as parts # T1001VPM and # T1003VPM as well as the cap as part # T1020 but if you need to replace that much it is much more cost effective to go with the whole unit that you referenced. I have linked our selection of RV sewer parts as well...
  view full answer...
• Difference Between 3 inch Hub and 3 inch Spigot for Doulbe RV Waste Valve Setups
  Basically the easiest way to describe it is that hubs fit over spigots. So the Double RV Waste Valves - Elbow - Rotating - 3 and 1.5 Hubs to 3 Lug Item # T80 that you referenced has a 3 inch fitting that is 3 inches in internal diameter designed for fitting over a 3 inch outer diameter (spigot) fitting. These kits do not come apart so you'd have to replace the entire thing.
  view full answer...
• RV Grey Water Fittings with 1-1/2-Inch Diameter
  We do have RV grey water valves and related items with a 1-1/2-inch diameter fitting. All connectors and fittings with this diameter are shown on the linked page; a second page showing valves like # T38 and # T80 is linked too.
  view full answer...
• Comparing the Double RV Waste Valves Part T80C and Part T80
  The difference between the Double RV Waste Valves part # T80C and part # T80 is that the former has a 1-1/2" spigot fitting and the latter has a 1-1/2" hub fitting. They both have 3" hub fittings as well. The spigot fitting means this will slide into the pipe and the hub fitting means this will slide over the pipe. The hub fittings are more common for the valves. In order to attach either assembly you will also need the Valterra ABS Solvent Cement part # A05-0303.
  view full answer...
• Replacement Waste Valves Needed for a 2000 Fleetwood Discovery Motorhome
  It actually looks like you have the Valterra Double RV Waste Valves # T80. This comes with both of the waste valves already installed and they can be rotated 360 degrees on the elbows for ease of installation. We do have replacement waste valves but to know exactly what you need you would have to take your current system apart. If it all comes off as one unit then you can install the # T80. If it comes apart differently please let me know and I can help you find the correct replacement...
  view full answer...
  
• Dimensions Of Valterra Double Rotating Waste Valve # T80
  I went to our warehouse and took some measurements of the Valterra Double Rotating Waste Valve, part # T80 for you. I have attached a photo of the valve that has the dimensions you asked about. The distance from the end of the 1-1/2 inch inlet pipe to the end of the 3-inch inlet pipe is 10-7/8 inches. The distance from the outside to outside of the square face plates is 8-1/2 inches and inside to inside between the plates is 5-3/4 inches.
  view full answer...
  
• What are the Differences between Valterra Hub and Spigot Waste Valve Adapters T80, T80C, and T80A
  The differences between the Valterra # T80, # T80C, and # T80A simply has to do with the types of connections that they have. They vary between Hub (female) and Spigot (male) ends to suit your needs. The ends that change are on the side. The top of each part number has a bayonet cap that fits over a 3" lug fitting for your sewer hose. Part # T80 has a 3" Hub (female) and a 1-1/2" Hub (male) Part # T80C has a 3" Hub (female) and a 1-1/2" Spigot (male) Part # T80A has a 3" Spigot (male)...
  view full answer...
  
• What is Difference Between Valterra RV Waste Valves T80 and T81
  The difference is the connection the two valves make after the valves come together. The part # T81 uses a spigot connection for a permanent install and the # T80 uses a bayonet style fitting which allows for easier connection and disconnection.
  view full answer...
• Difference Between Valterra Double Rotating Waste Valve T80 and T80C
  The difference is that the part # T80C has a spigot on the 1-1/2 inch side and the # T80 has a hub instead. A hub needs to mate to a spigot and a spigot mates to a hub. So you application determines which you would need.
  view full answer...
• Will The Valterra T80 Doublke Waste Valve Replace A LaSalle Bristol V93B1 Double Waste Valve
  I'm not able to find a good picture of the V93B1 to see exactly what type of connections it has (spigot or hub) so the # T80 could possibly work with your setup. The # T80 comes with hubs on both sides, which will slip over the existing straight pipes you have and can bond to them with ABS Cement # A05-0303. If you plan on cutting the V93B1 off and connecting the pipe into a new double waste valve then the # T80 would be a great choice. If the flanges where your VB93B1 connect are still...
  view full answer...
• What is the Difference Between Valterra Double RV Waste Valves # T80, # T80C, and # T80A
  The differences between the Valterra # T80, # T80C, and # T80A simply has to do with the types of connections that they have. They vary between Hub (female) and Spigot (male) ends to suit your needs. The ends that change are on the side. The top of each part number has a bayonet cap that fits over a 3" lug fitting for your sewer hose. Part # T80 has a 3" Hub (female) and a 1-1/2" Hub (male) Part # T80C has a 3" Hub (female) and a 1-1/2" Spigot (male) Part # T80A has a 3" Spigot (male)...
  view full answer...
  
• Can The Drain Rotate On The Dometic Double RV Waste Valves?
  The drain itself on the Double RV Waste Valves # T81 can not rotate, however the valve can rotate. You can check out the product overview video showing # T80 rotating as # T81 would rotate.
  view full answer...
• Can I Use PVC Cement with Valterra Waste Valves
  The Double RV Waste Valve part # T80 is more than likely correct for your 2010 Casita Spirit Deluxe. In order to be sure you will just want to take a quick measurement of the black and grey water lines. The black water line should be 3" diameter and the grey water line should be 1-1/2"diameter as this is standard for RV's but a quick check would confirm this. The PVC cement you have cannot be used with the Double RV Waste Valve as it is made of ABS, not PVC. The Valterra ABS Solvent Cement...
  view full answer...
• Recommended Double Waste Valve For A 2005 Roadtrek 190 Popular Motorhome
  To determine the correct replacement for your 2005 Roadtrek 190 Popular you'll want to just match how the pipes run since there a few different designs. The # T80 line has both the 3" and 1-1/2" lines running in horizontally to the main dump tube opening with different spigot and hub fittings on the ends for the connection. As long as each of these lines up correctly with how your pipes run you can use any of them and just un bolt the flanges on it and the old one and just swap it out....
  view full answer...
• Replacement Waste Valve Assembly for a 2007 Keystone Passport Ultralite
  I would love to help but I do not have any information that tells me what size drain pipes are on your 2007 Keystone Passport Ultralite so you will need to measure this for yourself. The standard size is 1-1/2" for the grey water tanks and 3" for the black water tanks. If this is what you have then you will want to use the Double RV Waste Valves part # T80. The grey water tank could also be a 3" diameter and if that is the case then you will want to use the Double RV Waste Valves part #...
  view full answer...
  
• Can the Valterra Double RV Waste Valves # T80 Be Rotated to Face Down
  Yes, you can undo the bolts on both sides of the closed valves of the Double RV Waste Valves # T80 and rotate it to face more down towards the hole. I am not sure how closely aligned that would make it because you'd have to rotate it to the next hole, not just exactly where you need it. You can see in the product photos that the # T80 valve typically has the handles coming straight out by the terminal outlet (like you pointed out), meaning whoever installed that valve has already rotated...
  view full answer...
  
• Direct Replacement For A Bristol Double Hub V93B15
  Product # 34466ND13AAR is a hub, a hub or a socket is the common female connection to PVC fittings. While # 34466ND13BAR is a spigot, which is the end connection to a fitting that has to be assembled into another fitting; the spigot fitting has the same outside diameter as pipe. The spigot fitting can be inserted into a hub or socket. The Double RV Waste Valves # T80 is a direct bolt on for your Bristol Double Hub V93B15.
  view full answer...

Do you have a question about this RV Waste Valve?