What is Difference Between Valterra RV Waste Valves T80 and T81

Question

Question:

I have a 2012 Casita and I need a new Valterra Double RV Waste Valve. I understand the difference between the A, B, and C designations. What is the difference between the T80 and T81, and which do you recommend for my Casita?

asked by: Alan L

0

Expert Reply:

The difference is the connection the two valves make after the valves come together. The part # T81 uses a spigot connection for a permanent install and the # T80 uses a bayonet style fitting which allows for easier connection and disconnection.

expert reply by: Jameson C

0

Answer 1

Product #34466ND13AAR is a hub, a hub or a socket is the common female connection to PVC fittings. While #34466ND13BAR is a spigot, which is the end connection to a fitting that has to be assembled into another fitting; the spigot fitting has the…

view full answer...

Answer 2

Yes, since I was able to see a picture of your current valve setup I can tell that the Bristol Double RV Waste Valves #34466ND13AAR that you referenced is exactly what you'd need. The valves of this kit will fit over the 1-1/2 inch and 3 inch…

view full answer...

Answer 3

The distance between the 3" entry and the 1.5" entry on the Bristol Double RV Waste Valves #34466ND13AAR is 10-1/2". I've attached a picture for you showing some additional measurements as well.

view full answer...

Answer 4

The differences between the Valterra #T80, #T80C, and #T80A simply has to do with the types of connections that they have. They vary between Hub (female) and Spigot (male) ends to suit your needs. The ends that change are on the side. The top of each…

view full answer...

Answer 5

Thank you for the pictures of your LaSalle Bristol V93B1, it made it a lot easier to find the correct replacement to get your RV's sewer system back in working order. The V93B1 appears to just be the actual drain pipe with the gray dumping into…

view full answer...

Answer 6

The difference between the three Valterra Double RV Waste Valves referenced in your question has to do with their fittings, specifically their use of hubs or spigots. Basically a spigot (also referred to as the "male" fitting) will go…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 12

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

What is Difference Between Valterra RV Waste Valves T80 and T81

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching