Trailer Spindle Nut 1"
(384 reviews)
Price: $10.36
In Stock
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Need help with installation?
Locate installers near me- All Info
- Reviews (384)
- Q & A (0)
- Videos (1)
- Photos
TruRyde Accessories and Parts - 165686
- Trailer Spindles
- Spindle Nut
- TruRyde
- 1 Inch I.D.
Castle nut for 1" spindles. Bare metal finish.
Features:
- Castle nut for 1" spindles
- Bare metal finish
Specs:
- Size: 1" diameter x 0.532" tall
- 14 Threads per inch
FA-SN100 TruRyde Trailer Spindle Nut - Raw
Video of Trailer Spindle Nut 1"
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Video Transcript for Review of TruRyde 1 Inch Diameter Trailer Spindle Castle Nut - 165686
Hi, everybody. Andy here with etrailer.com. And today we're just gonna take a very quick look at this trailer spindle nut. This bare metal finish castle nut is for one-inch spindles. So it has to have one inch in diameter, and the overall height, just to be very specific, is gonna be 0.532 inches tall, and this is 14 threads per inch. And that's gonna conclude our brief look today.
I do hope that it was helpful for you. Again, my name is Andy. Thank you for joining me..
Customer Satisfaction Score:
99% were satisfied with this product
1% of customers were not satisfied
- Wrong item was ordered
- Arrived Damaged
- Product did not meet expectations
Customer Reviews
Trailer Spindle Nut 1" - 165686
Average Customer Rating: 4.8 out of 5 stars (384 Customer Reviews)
Castle nut for 1" spindles. Bare metal finish.by: Brian F05/09/2024
good quality and a good price. perfect fit
by: Craig 04/11/2024
Worked out great when needed during a roadside repair.
Already ordered another backup.
by: Rob07/12/2019
exact replacement, they shipped it fast,always great prices and in stock,
I just Rebuilt my trailer using etrialer for all the parts, brake lights bearings winch,they even had all the parts to rebuilt the hyd actuator
by: Steven 05/10/2024
Fit as advertised
by: Dan11/03/2023
great website, easy to order from, quick shipping! Customer Service is quick to respond to questions
Thanks,
by: Adam 04/08/2024
Worked perfect
by: Bruce 04/03/2024
Need them quick and they made it happen a day sooner than expected … Thank you
by: Gregory 05/02/2024
Just what we wanted!!!
by: Roger08/01/2023
Did not fit axle spindle so I'll be returning the 2 nuts. Had to get correct size locally so I could finish assembly.
by: JosephA01/31/2024
Worked very well. On a difficulty scale of 1-10, with 10 being the hardest, this was a 3.
by: Jesse 03/28/2023
After being in storage, in a field, for more than 2 years, Water had contaminated the original hub, pitting the bearings and races and they had not been serviced since, at least 1999. I polished up the EZ lube spindles, flushed out the old grease and I was ready. Everything fit perfectly. It was aa perfect match. Used new Nuts and Washers. re-installed the Wheels and Tires, Torqued to 90-10lb. The old 6 x 4 Wells Cargo trailer is once again Ready for the coming rendezvous season.
by: Robert H02/10/2024
Thanks for getting it shipped so quickly - well done!
by: Carl12/14/2022
The products appear to be ok. I would give the products 4 out of 5 stars. The 2 star rating is because of the poor shipping.
I ordered 2 leaf springs, 2 spindle nuts and 3 spindle washers. The first box showed up quickly (3 days) but it only contained 1 leaf spring. I called etrailer and they shipped a second leaf spring. After 5 days the package was at my local UPS distribution center but the tracking info said the package had been damaged and ups was contacting the shipper. I found out from ups that the spring had come out of the box, and they did not know who to deliver the spring to. I called etrailer again to discuss the damaged package but etrailer would not ship another spring until the damaged box/loose spring mystery was solved. Another week passed. I finally got the second leaf spring today, but it took about 3 weeks from the initial order date.
by: John M02/11/2014
Brake Drum/Hub unit and associated parts arrived quickly and in great shape! Waiting for warmer weather to install. Have used e-trailer parts before to rebuild all brakes, hubs and bearings on camping trailer last summer but over-torqued one bearing set and had an outer bearing failure - almost lost the wheel! This unit will replace that damaged hub which was gouged by riding on the washer and spindle nut causing grease cap not to seal and leak grease. These parts are first class and fit and install perfectly!
by: Randy 04/11/2023
Great products and fantastic customer service,they really go out of their way to try to help you get the correct parts,delivery is fast.
by: Robert 11/20/2023
Very quick shipping and great communica tion!
by: Don 11/15/2023
quick service good prices
by: Thomas05/18/2022
has performed as expected would buy aga in
Tom C.
5/19/2023
part is working as expected would buy again
by: Peter08/28/2023
great process and people, fast knowledgeable and efficient
by: Samuel 08/24/2023
Very easy to place order! Website is user friendly!
by: James Sponheimer 07/09/2015
Mike H. Was really helpful & knowledgable . Thx for all ur help !
by: Jim06/19/2020
First off I purchased 1" castle nuts, tang type spindle washers and 2 wheel hubs for a 3500 lb tandem trailer. I wish I had pictures during the assembly but I don't, however these parts all assembled perfectly. The hubs were pre-greased, so all I did was use brake cleaner on the wheel spindles to clean up, the hubs slid on with no problem, the tang washers fit perfectly and the castle nut threaded on with ease, the hub included new lug nuts which made the whole repair a breeze! Very pleased with the purchase and ease of assembly, I was going to piece out the bearings and races but for the price of a complete hub it made more sense to buy it already greased and assembled. E trailers videos and instructions are great to consider before attempting to install the parts.
by: JohnM05/09/2023
The part is what I ordered. But what is almost as important is the inside sales person who helped me with my order. MarthaO was so much better than average and an example for every other inside sales person to emulate. Thank you Martha!
by: Frank Venturella05/03/2019
6 wks. ago I started on a refurbishing project off a 1988 Holsclaw boat trailer. I stripped all the paint off, ground and sanded the rust, primed and painted everything, replaced ALL the fasteners with stainless stell and some galvanized. I ordered several things from etrailer.com . Everything I ordered was to exact specifications and the shipping was on-time, everytime. I ordered several bearing items to repack the hubs, this coupler and nifty lifting handle, transom tie down brackets, spare tire carrier and 3 new 570x80 tires mounted on galvanized rims and the company installed stems, free of charge! I love the way this project came out and I've thoroughly enjoyed shopping @ etrailer.com! Thank you!
by: Ned05/11/2022
Nice upgrade of the axle on my [online] trailer. I had no confidence towing my home made teardrop camper until I installed this axle. The package was damaged in shipping and eTrailer quickly replaced the missing parts.
25
384
Show More Reviews
See what our Experts say about this TruRyde Accessories and Parts
- Replacement Hub for Adams Trailer with Dexter EZ Lube Axles with Bearings L44649We have just the hub you are looking for with the part # AKIHUB-545-2-EZ-2K. This matches the bearing and seal info you listed, the bolt pattern, has an ez-lube cap for access to the grease fitting, and comes pre-greased so it's ready to install. You will need new castle nut part # 165686, and then for standard cotter pin # 165649, for a tang washer part # 5-101, and for a D washer part # 5-23.
view full answer... - Where Does Flat Washer GoI was unable to find an order number so I'm not certain exactly what you are referring to, but in general a flat washer such as Washer For 1" Spindle # SW1000 will go between the outer bearing of your hub and the nut that holds it on, which essentially works to protect the bearing. These washers are used on spindles with a spindle nut such as Spindle Nut 1" # 165686 and Cotter Pin # 165649.
view full answer... - Does 84 EZ Lube Spindle TRU77FR Come with Castle NutThe #84 E-Z Lube Spindle w/ Brake Flange for 3,500-lb Trailer Axles Item # TRU77FR does not come with a castle nut so you'd need to order that as well with part # 165686.
view full answer... - What Is The Tread Size For The # 42 Spindle?The #42 E-Z Lube Spindle w/ Flange # TRU37FR has a 1"-14 thread size. A replacement Trailer Spindle Nut # 165686 is available if the treads are damaged on the castle nut.
view full answer... - Does Trailer Idler Hub Assembly AKIHUB-545-2-EZ-1K Include Spindle Nut?The Trailer Idler Hub Assembly # AKIHUB-545-2-EZ-1K you were looking at does not include a spindle nut, but does include new bearings # L44643, races, grease seal, grease cap, and lug nuts. Typically customers reuse there current spindle nut, but if yours is missing/lost or damaged you should be able to use 1" Spindle Nut # 165686 as that is the typical spindle nut used for an axle that uses the above hub. You can confirm this by measuring the diameter of the threaded portion of your spindle...
view full answer... - How to Choose the Correct Pre-Greased Replacement Hub for Snowbear TrailerThere are pre-greased hubs available in a 5 on 4-1/2 bolt pattern. In order to find the correct replacement hub you can take apart your good hub assembly and look at the bearings themselves; wipe away the grease and you should be able to see the part number stamped directly on them. If your hub has inner and outer bearings # L44643 you'd need CE Smith Trailer Hub Assembly w/ Carrying Case for 2,500-lb Axles - 5 on 4-1/2 - Pre-Greased # CE13210. Should your hub have inner and outer bearings...
view full answer... - Castle Nut Wont Thread All the Way on 2,000 lb EZ Lube Spindle with Tang and D WasherThank you for all the photos! My contact at Dexter Axle confirmed that on a 2,000 lb axle, the D-washer # 5-23 is not needed. It is only required on 3,500 lb axles and above. So, in your case it's perfectly safe to leave it off and this way allowing the castle nut # 165686 to fully thread on the spindle. When tightening the spindle nut it should be tightened to the point that you can feel resistance in the bearings, then backed off to the point where you can bend the tang properly which...
view full answer...
- Replacement Axle Nut for 3500 lb Boat Trailer AxlesWe have what you need! For EZ-Lube axles which are very common on boat trailers you want to use the Spindle Nut Kit for EZ Lube Axles part # RG05-100. This will have two nuts, washers and keepers. For the non EZ-Lube axles use the Trailer Spindle Nut 1" part # 165686 and the Cotter Pin part # 165649. these are individual so you will want two of each to have all you need. You can confirm these will fit on your axles by measuring your spindle and ensuring that your it has 1" threads on it.
view full answer... - Are There Shims for a Trailer Axle Castle NutI do have some advice for you but we don't carry any spindle shims for the castle nut. I've messed with many spindles and castle nuts, there are a lot of times it seems there is one notch that's too loose and one that's too tight. I recommend the slightly tighter setting if needed, you don't want any side to side play in the hub when tight. This can cause grooves to wear into the spindle over time and destroy the axle.
view full answer... - Spindle Nut for Use with Trailer Hub # AKIHUB-545-2-LF-2KFor a spindle nut to use with the hub # AKIHUB-545-2-LF-2K that you referenced the part # 165686 would be a great replacement. You'd also need a cotter pin if you didn't have one as well with # 165649.
view full answer... - Why Do Some Spindles Use Cotter Pins and Others Use a Tang Washer? The #42 Spindle # TRU57FR does come with a Standard Washer # SW1000, Cotter Pin # 165649, and Castle Nut # 165686 to secure the hub to the spindle. The D-Washer # 5-23 and Tang Washer # 5-101 were created to allow for a Grease Zerk # LC44XV to fit the end of the spindle and allow you to grease the hub bearings without removing the hub. There are some versions using a grease zerk and cotter pin but those are more likely to not allow grease to reach the bearings as it can come out the cotter...
view full answer... - How Tight Does the Castle Nut on a Trailer Spindle Need To BeAccording to our installers you will tighten the trailer spindle nut until it stops by itself. In other words do not torque it down as hard as you can. It just has to be tight. A little play is to be expected. You do not want to torque it down too tight, because that makes the bearings too tight and then that generates heat and your bearings come apart. You might want to try tightening it a few times to get a feel for where it seems like the spindle nut naturally stops. Once it is fairly...
view full answer... - Recommended Castle Nut for Dexter Trailer Axle Beam # T3584F-EZ-8974The spindle on your Dexter Trailer Axle Beam # T3584F-EZ-8974 will use a 1 inch castle nut with 14 threads per inch like the TruRyde # 165686. Then for a washer you can use # SW1000 and for the cotter pin you will need # 165649.
view full answer... - Replacement Galvanized Trailer Idler Hub For a Continental EC39 Boat TrailerYour Continental EC-39 Boat Trailer will need a Trailer Idler Hub Assembly # AKIHUB-545-2-G-2K. I was able to confirm with Continental that you have a spindle that uses 1.063" bearings on a straight spindle with a 1.249" ID grease seal. You will need to replace the grease seal that comes with the kit with a Double Lip Grease Seal # 34823. If your Cotter Pin # 165649, Washer # SW1000, or Spindle Nut # 165686 are damaged or missing we have those items available for replacement as well....
view full answer... - Replacement Bearings, Seal and Spindle Nut for Dexter D52 Trailer AxleFor a kit that has all of the bearings and seal for your Dexter D52 5,200 lb axle you'd want the kit part # BK3-310 and then for a spindle nut you'd want the # 165686.
view full answer... - How to Determine the Correct Hub Cap Cover for a 5 Lug WheelI have not heard of a 5 on 4.3" hub cover, so I believe that there might be some incorrect measuring. Using the guide attached, I recommend re-measuring your wheel bolts. I believe you have 5 on 4-1/2" as that is the most common, however if you measure: -2 5/8", then you have a 5 on 4-1/2 bolt pattern, -2 3/4", then you have a 5 on 4-3/4 bolt pattern, -3", then you have a 5 on 5 bolt pattern, Or - If you measured 3 1/4", then you have a 5 on 5-1/2 bolt pattern.
view full answer...
- Can Performance Tool Installation Set Be Used On Grease Seal With Diameter Of 3.37 InchesThe discs that are included with part # PTW83020 include discs that have a diameter of 2.47 inches and 2.555 inches. The inside diameter of the 10-36 Grease Seals, part # RG06-070 is 2.25 inches so the tool with the larger disc will work for installation. You will want to make sure you have the tool centered properly so you catch the outer ring of the seal when using it to install. A socket is normally not used on a spindle nut like part # 165686. Typically channel locks are used...
view full answer... - Spare Hub And Bearings For A Kodiak Rotor/Hub 133-7K-8Hey Alex, thanks for providing that part number. You may already know this, but what you have are the standard Kodiak 7K rated 8 lug hub and rotor assemblies. We have all of the parts you need, and I have listed those for you below. - Hub/Rotor Assembly # KRH1378D - Bearing Kit # DBRKHW7 - Cotter Pin # 165649 - Spindle Nut # 165686 The aforementioned bearing kit will include your seals and grease caps. Keep in mind the bearing kit comes with enough for two axles. All of the other parts...
view full answer... - Torque Rating for Spindle Castle NutWhen installing the castle nut on the end of the spindle, there is no specific torque rating. The nut is ran down until there is no side to side play in the hub, and then backed off to the next notch in the castle nut so the tang washer or cotter pin can secure the nut. Over-tightening the castle nut can damage the bearings, races and spindle. If you click on the video link I provided, and fast forward to the 4:45 minute mark, you can see the procedure.
view full answer... - Availability of a Replacement Castle Nut for a Harbor Freight Trailer25 mm is very close to 1 inch, so there is a good chance the castle nut part # 165686 would fit as it is 1 inch. That said we've had customers tell us it's actually 22 mm which we don't carry.
view full answer... - Correct Hubs-Drums and Brakes for Lippert 3,500 lb SpindleThe Lubed 4" Drop Spindle with Brake Flange for 3,500-lb Axle # LC12338, uses standard 10" diameter hubs and brakes, for which we have the Electric Trailer Brake Kit - Self-Adjusting - 10" - Left and Right Hand Assemblies # AKEBRK-35-SA. For the brake mounting hardware (nuts and lock-washers) you can use part # BRKH10B. The most common hub-drum assembly for this application is part # AKHD-545-35-EZ-K, with a 5 on 4-1/2 wheel bolt pattern. However, depending on the wheels you plan on using,...
view full answer... - What Size Socket Works with 1 Inch Spindle Castle Nut # 165686?The TruRyde Spindle Nut # 165686 has an outer measurement of 1.45 inches. You will use a 1-1/2 inch socket on this castle nut or we usually use a channel lock for these installations. I've attached a video of an installation of a hub to assist. You don't want to torque these down tight as you do want to have slight movement and the cotter pin will keep it in place.
view full answer...
- Installation of Electric Brake Replacement Assemblies on Wells Cargo Dual Axle Trailer When installing electric brakes on your Wells Cargo tandem axle trailer, you will want either the Electric Trailer Brake Kit - Self-Adjusting - 12" # AKEBRK-7-SA or the 10" # AKEBRK-35-SA. You can simply put a tape measure on your hub to see which one you need. I've attached videos of the installations to assist. It is just as common for assemblies not to use a cotter pin and it is for them to use a cotter pin on that spindle nut. Some will use a castle nut like # 165686 with the cotter...
view full answer... - Replacement Spindle Washer, Castle Nut and Cotter Pin for Dexter SpindleThe linked page displays all the trailer spindles we offer and specs including weight capacity and thread diameter. All spindles we offer have a 1-inch-diameter threaded portion that accepts a spindle washer like # SW1000 and a castle nut like # 165686. For a cotter pin you can use # 165649.
view full answer...
Do you have a question about this Accessories and Part?
Info for this part was:
Expert Research:
Mike L
Expert Research:
Jameson C
Expert Research:
John H
Updated by:
Wilson B
Updated by:
Noah M
Installed by:
Andy C
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Product Experts Available Now!
Call 1-800-940-8924
John M.
2/11/2015
Replaced old hub, bearings and castle nut. Everything working well - no problems and fit was perfect! Ill use etrailer everytime!