Tang Replacement Spindle Washer

See what our Experts say about this Redline Accessories and Parts

• Spindle Nut Washer and Grease Seal for a Dexter 3500 Pound E-Z Lube Trailer Axle
  The Replacement Spindle Washer, # 5-101, was designed specifically for E-Z Lube axles, so that should be the correct washer for you. You can make sure that your spindle has a 1 inch diameter at the end where the washer will be. It sounds like you have a #84 spindle which is for 3500 pound E-Z lube axles. The correct seal would be # RG06-050, for a pair of double lip seals. To be sure, you would need to find the bearing numbers of the inner and outer bearings. The numbers are stamped into...
  view full answer...
• Type of Spindle Washer Used on Boat Trailer Spindle with a Notch/Slot on Spindle
  Actually what you have is pretty standard. It's a tang washer setup. We have the part # 5-101 or part # 5-71 which are similar styles. I attached a picture of what the part # 5-101 is designed to fit.
  view full answer...
  
• Is a Spindle Washer Needed Between the Spindle Nut and Outer Bearing on Dexter 5 on 4-1/2 Hubs
  Yes, there should be a washer of some type between the spindle nut and the bearing on your trailer. The washer protects the back side of the bearing from the edges and points on the back side of the spindle nut. There are several types of spindle washers available depending on the spindle configuration on your trailer. The Washer For 1 inch Spindle, # SW1000, is typically used on spindles that have a castle nut, like # 165686, and a cotter pin, # 165649. A D washer, # 5-23, would be...
  view full answer...
• Should There Be a Washer on Trailer Spindle Between Spindle Nut and Outer Bearing
  There really should be a flat washer between the outer bearing of your hub and the nut that holds it on. The washer protects the back side of the bearing from the edges and points on the back side of the spindle nut. The Washer For 1 inch Spindle, # SW1000, is typically used on spindles that have a castle nut, like # 165686, and a cotter pin, # 165649. A D washer, # 5-23, would be used on a spindle that has a flat side and uses the same castle nut and cotter pin setup. A Tongue Washer,...
  view full answer...
• Tongue Washer Compatibility with Trailer Spindle and Tapered Bearings
  The Tang Replacement Spindle Washer # 5-71 or the Washer Spindle Tongue # 165863 will fit into the groove of your spindle to keep the washer and nut from rotating. This gives you a similar outcome to the tang style washer that uses the cotter pin to hold it, but the idea is the stabilization of that washer that will keep slight pressure on the flat side of the tapered bearing to hold it in place. This is one style similar to a D style washer as well like Spindle Nut Kit for EZ Lube Axles...
  view full answer...
• Availability of Dexter Part Numbers 005-070-00 006-096-00 005-071-00 010-050-00 021-036-00 046-032-0
  We have the part # 46-32, # 6-96, # 5-71, # RG04-270 and the part # 010-050-00 but we do not have the other part you mentioned.
  view full answer...
• Tang Spindle Washer With 1 inch Diameter
  The only tang spindle washer we offer with a 1 inch diameter is TruRyde part # 5-101 for an E-Z lube spindle. It does have two prongs to bend down over the castle nut. The Redline washer part # 5-71 is 1-1/2 inches in diameter. I have attached a video for your reference.
  view full answer...
• Should There Be a Washer on Trailer Spindle Between Spindle Nut and Outer Bearing
  There really should be a flat washer between the outer bearing of your hub and the nut that holds it on. The washer protects the back side of the bearing from the edges and points on the back side of the spindle nut. The Washer For 1 inch Spindle, # SW1000, is typically used on spindles that have a castle nut, like # 165686, and a cotter pin, # 165649. A D washer, # 5-23, would be used on a spindle that has a flat side and uses the same castle nut and cotter pin setup. A Tongue Washer,...
  view full answer...
• Replacement Washer for an EZ Lube Trailer Spindle
  EZ lube spindles generally use a tang washer to prevent the castle nut from turning. There are different sizes available depending on what is needed. For example, # 5-101 has an inner diameter of 1 inch. Washer # 5-71 has a different design and a 1-1/2 inch inner diameter. Washer # 5-59 is similar but larger with a 1-3/4 inch inner diameter. Sometimes you will see a D-shaped opening on an EZ spindle washer such as # 5-23. On this one the distance from the straight edge to the furthest...
  view full answer...
• Replacement Spindle Washer for Axle with Bearings that are 1-3/8 and 1-1/16 inch
  Based on the spindle dimensions you have the tang washer you'd need is the part # 5-71.
  view full answer...
• Tang Style Washer for Trailer Spindle with Castle Nut
  It sounds like you are looking for the Replacement Spindle Washer - Tang Type for E-Z Lube # 5-101 if you have the D shaped spindle. If you don't then you will want the Tang Replacement Spindle Washer # 5-71 which has a 1-1/2 inch inner diameter or the Dexter Tang Washer - Type B # 5-59 which has a 1-3/4 inch inner diameter.
  view full answer...
• Availability of Trailer Spindle Washers with Tabs
  If you are talking about a washer like # 5-101, we have them. I cannot speak for any auto parts store but etrailer is here for you. We also have some other tang washers: # 5-59 or # 5-71.
  view full answer...
• Inner Diameters of Tang Washer Type B
  The only two Tang Washer - Part B that we carry are the Tang Replacement Spindle Washer # 5-71 which has a 1-1/2 inch inner diameter and the Dexter Tang Washer - Type B # 5-59 which has a 1-3/4 inch inner diameter.
  view full answer...
• Causes for Hub Castle Nut to Come Loose After Installing and Using Hubs
  A tang washer like # 5-101 or # 5-71 has a tab to secure the castle nut on the spindle so that it cannot rotate or back off on the threads. If the tang washer tab (or a cotter pin) is still in place in the notch on the castle nut (as in the linked photo) the nut should not be able to move. The only other place where slack in the hub's fit could develop is at the back side where the grease seal installs. This is the portion of the spindle noted by the arrow in the linked diagram. If the...
  view full answer...
  
• Inner Diameter of Tang Spindle Washers Close to 1-5/8 Inches
  We have two replacement tang spindle washers with different inner diameters close to 1-5/8 inches similar in style to # 5-71, but none with that exact inner diameter. The options are the following: - 1-1/2" Inner Diameter: Tang Replacement Spindle Washer # 5-71 - 1-3/4" Inner Diameter: Dexter Tang Washer - Type B # 5-59
  view full answer...
• Replacement Spindle Washers For An Old Trailer With 10k Axles
  We carry a variety of different spindle washers so you'll want to measure your current washers and note the design to match it up to the correct design for your spindles: Replacement Spindle Washer - Tang Type for E-Z Lube # 5-101 Washer For 1" Spindle # SW1000 (most common) Tang Replacement Spindle Washer # 5-71 D Washer for EZ Lube Spindles # 5-23 Washer Spindle Tongue # 165863
  view full answer...
• Inner Wheel Bearing Recommendation for a Number 84 Spindle
  The inner and outer bearing surfaces on a number 84 spindle are different diameters. The outer bearing will ride on a 1.00 inch diameter surface and the inner bearing will ride on a 1.378 inch surface. It sounds like you have the correct outer bearing and now are in need of the correct inner bearing. For that you would want the part # L68149 that you referenced. You will want to use a spindle washer. The washer protects the back side of the bearing from the edges and points on the back...
  view full answer...
• Trailer Spindle Washer with a 1-1/2 Inch Inner Diameter
  We have a tang washer, # 5-71, which has a 1-1/2 inch inner diameter. I have linked a video of it for you. It is the only spindle washer we have with a 1-1/2 inch inner diameter.
  view full answer...
• Replacement Spindle Washer For 3,500 Lb EZ Lube Spindle
  For a 3,500 lb EZ Lube axle, the replacement spindle washer you will need is part # 5-101. This washer has an inside diameter of 1 inch, so you may want to measure the spindle diameter to be certain. We do offer other replacement spindle washers, like part # 5-71 for 1-1/2 inch spindles, and part # 5-59, which is for spindles that measure 1-2/4 inches.
  view full answer...

Do you have a question about this Accessories and Part?