T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector

See what our Experts say about this Tekonsha Custom Fit Vehicle Wiring

• Recommended Trailer Hitch Receiver And Components For 2011 Chevy Impala
  There is not a 2 inch receiver available for a 2011 Impala. Only the 1-1/4 inch options like the Draw-Tite # 36407 and the Curt # C12252. Both of these hitches have a rated tongue weight of 300 lbs and towing capacity of 3500 lbs, so even with the smaller receiver, they can still handle some weight and are usable for light-duty towing. If you will be using this hitch receiver for towing, I recommend the Class II Drawbar 3-1/8" Rise (Kit) # 36061 along with the 2 inch hitch ball like...
  view full answer...
• Uhaul Trailer Wiring Harness Causes Brake Light and Blinker to Not Work on 2009 Chevy Impala
  The wiring harness used on your 2009 Chevy Impala must not be grounded properly or it is possible that there are bent or broken pins in the harness they used. The ground needs to be attached to clean and corrosion free bare metal surface. There can't be any paint or coating either. Check the connectors for the harness to see if there are any bent or broken pins. A bent pin might be able to be bent back but if a pin is broken the harness will need to be replaced. I recommend # 118417. I...
  view full answer...
• Parts Needed for 2011 Chevrolet Impala to Allow Towing Power Chair on Utility Trailer
  You are correct that the 1-1/4-inch Class II hitches made for your 2011 Chevrolet Impala have a tongue weight rating of 300-lbs. This means that you cannot transport a 445-lb powered wheelchair on any hitch-mount carrier, but you can use a small trailer. The hitch I recommend is Draw-Tite # 36407 that you referenced. It offers a no-drill installation and costs less than the same-capacity Curt model. An installation video is linked for you along with the written instructions. For a compatible...
  view full answer...
• Parts Needed to Install a P2 Trailer Brake Controller on a 2013 Chevy Impala
  The 2013 Chevy Impala and most other cars do not have tow package wiring so there is no wire bundle or plug in port under the dash to plug in a brake controller. It will be a hardwire installation. The best place to run the wires from the controller to the battery would be at or near an existing harness that goes through the firewall. Ideally, you would run the wire without making any additional holes. But sometimes, there is no space at all to shove a wire through at an existing exit/entry...
  view full answer...
• Bolt Leader and Wiring Harness for a 2007 Chevy Impala
  All of the hitches sold on our website come with the necessary hardware to install the hitch on its respective vehicle, but do not include the tools. If you should decide you need to purchase a bolt leader for the installation of the Draw-Tite Class II Trailer Hitch Receiver, item # 36407, you will need the 1/2 inch Bolt Leader, part # 80101-1. The T-One Wiring Harness for your 2007 Chevy Impala is sold separately from the hitch, and it is the T-One Vehicle Wiring Harness, item # 118417....
  view full answer...
• Recommended 6-Way Wiring Harness for 2013 Chevrolet Impala
  I would be happy to help you. The connector on your 2018 Aspen camper is a 6-way connector. In order to get a 6-way connection on your 2013 Chevrolet Impala you will need to start with a 4-way. For a 4-way, I recommend the # 118417 T-One Vehicle Wiring Harness from Tekonsha. This is a custom fit wiring harness and plugs directly into connection points behind the passenger's-side tail light. For the 6-way connection, you want the # ETBC6 Universal Installation Kit. This includes all of...
  view full answer...
• Trailer Hitch and Towing Capacity of a 2008 Chevrolet Impala
  From my research the 2008 Chevy Impala can tow up to a 1,000 pound trailer. You want the loaded trailer to stay under 1,000 pounds. As far as not scraping the ground I'm not sure what you're referring to but if the trailer is not overloaded and is loaded with the tongue weight between 10 and 15 percent of the trailer's weight then you shouldn't have any issues. You also want to make sure the trailer is level when towing. As for the hitch receiver I recommend the Draw-Tite # 36407. ...
  view full answer...
• Recommended Hitch And Combination Transmission/Oil Cooler For 2009 Chevrolet Impala
  For your 2008 Chevrolet Impala, I recommend the Draw-Tite Trailer Hitch, part # 36407. This is a Class ll hitch and has a 1-1/4 inch receiver opening. The drawbar I recommend for this hitch is part # 36061. This features a 3-1/8 inch rise, and uses a hitch ball with a 3/4 inch diameter shank. This includes the pin and clip. For a 1-7/8 inch hitch ball I recommend part # 19257, and for a 2 inch hitch ball I recommend part # 19258. Transmission and oil coolers are not vehicle specific....
  view full answer...
  
• Why Does Hopkins Trailer Wiring Harness Install Differently than Others for a 2011 Chevy Impala
  The Curt wiring harness # C56046 as well as the Tekonsha harness # 118417 both plug into just one side of the 2011 Chevy Impala. The main tail light wiring harness that runs from the front to the back of the vehicle is located on that side so it is possible to just tap into that harness. The Hopkins harness # HM11141595 is just a different design. The connectors for the passengers side do not have the wiring in them to get the signals for the left side of the vehicle like the other harnesses...
  view full answer...
• Availability of Trailer Wiring Harness for 2007 Chevy Monte Carlo
  To install a 4-pole trailer connector on your 2007 Chevy Monte Carlo, I'd recommend part # 18252. This trailer connector would need to be tapped into the existing taillight circuits but the included circuit tester would make installing the trailer connector pretty simple. You'll need a helper to sit in the driver's seat for you. Begin by accessing the rear of the taillight assemblies as you would if you were changing a burned out taillight bulb. Find the vehicle's taillight wiring harness...
  view full answer...
• Trailer Hitch Installation Instructions, Drawbar, Hitch, Ball, and Wiring for a 2007 Chevy Impala
  There are basically 6 steps to install the Draw-Tite Trailer Hitch, # 36407, on your 2007 Chevy Impala. First, the exhaust must be lowered. Next, install the carriage bolts and blocks through access holes in the vehicle frame on both sides. Then, install carriage bolts and blocks through access holes in the vehicle cross member. Next is to raise the hitch into position and use the washers and nuts to secure the hitch. Then, tighten the nuts to the torque rating specified in the instructions...
  view full answer...
• Recommend Correct Trailer Wiring For My 2010 Chrysler Sebring
  For the correct wiring for your 2010 Chrysler Sebring, you would need Draw-Tite Custom Fit Vehicle Wiring, part # 118444, which plugs in-line with your tail light wiring connectors and connects to your battery via included fuse. The item you selected, T-One Vehicle Wiring Harness, part # 118417 is designed to fit the 2006-2011 Chevrolet Impala. The item you referred to, 4-Pole 60 Inch Long Vehicle End, part # 18002, will not work for on your Chrysler Sebring as it has a 3-Wire System...
  view full answer...
• Troubleshooting Stop/Turn Signals Not Functioning on a 2013 Chevy Impala with Tow Ready Harness
  Most likely the problem is the grounds of your trailer wiring since the stoplight/blinker circuits require more amperage and that's typically where an insufficient ground problem shows up. Here's how you will test everything though: First thing you should do at this point is test the 4-way of the wiring harness with a circuit tester part # PTW2993 for voltage on all of the right pins when the taillight signals are being applied. Just like in the video I attached. If the voltage checks...
  view full answer...
• Recommended Trailer Hitch and Ball Mount for 2013 Chevy Impala to Tow a Utility Trailer
  For your 2013 Chevy Impala, I recommend the Curt Trailer Hitch Receiver - Custom Fit - Class II - 1-1/4" # C12252. This is a custom fit that will allow you to use the Curt Class II Drawbar # C45522 along with hitch ball # C40018 and pin/clip # F-4. If you need trailer wiring, I recommend the T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # 118417 which will plug into the factory harness located behind the passenger side tail light assembly. Then you will be able to...
  view full answer...
  
• Will the Draw-Tite Class II Trailer Hitch # 36407 Fit on a 2009 Impala LTZ with Dual Exhaust
  Yes, the Draw-Tite Class II Trailer Hitch, item # 36407, is designed to work with the dual exhaust models. There is not a lot more time, or trouble, required for installation on dual exhaust models. The only difference is that you have to lower the drivers side exhaust as well as the passengers side. We have an installation video on a 2007 model that has the dual exhaust for you to review, see link. I have also included a link to the installation instructions for you to review. Some...
  view full answer...
• Can a 2008 Chevrolet Impala LTZ Tow a Snowmobile
  Your owners manual is the best resource to use when determining towing capacities of your vehicle, see section 4. I found a copy of the owners manual for a 2008 Chevrolet Impala and Chevy states that an Impala can tow a trailer, but the gross trailer weight must not exceed 1,000 lbs. Keep in mind, Chevy gives the Impala a maximum towing capacity of 1,000 lbs assuming the driver is the only additional weight in the vehicle. If there will be additional passengers and cargo in the vehicle,...
  view full answer...
• Trailer Hitch Comparisons and Recommendation for a 2012 Chevy Impala
  Hidden Hitch and Draw Tite are both made by the same company so basically they are the exact same with the exception that the Hidden Hitch part # 90137 (no longer available) comes with a ball mount and a pin and clip and the Draw Tite part # 36407 does not come with this. Curt is it's own company so the part # C12252 would be similar but made by a different company. The biggest disadvantage to Curt is the requirement of a stabilizer strap like part # 18050 when used with a non-supported...
  view full answer...
• What Trailer Hitch And Wiring Harness Is Recommended For A 2005 Chevrolet Impala
  I would recommend the Draw-Tite Class II 1-1/4 Inch Hitch # 36407. It is a Class II hitch with a 3,500 lbs. towing capacity and a 300 lb. tongue weight capacity. I am sending a link to the installation instructions on the hitch. If you will be towing with the hitch, you will need ball mount part # 36061. You will also need a hitch ball like the Tow Ready 2 Inch Hitch Ball # 19258. For wiring, you will use the Curt Wiring Harness # C56116. This harness will plug into the vehicles taillights...
  view full answer...
• Could 2008 Chevy Impala Transport Dirt Bike
  Motorcycle carriers like the Ultra Fab part # UF48-979033 that you referenced require a 2 inch size trailer hitch installed on the vehicle they are used with. Your 2008 only has 1-1/4 inch hitches available like the Draw Tite hitch part # 36407. Only way you'd be able to transport a dirt bike with your Impala would be with a trailer and this hitch. For a ball mount you'd want the part # 36061, hitch ball # 19257, and trailer wiring # 118417.
  view full answer...
• Will the Trunk Open on a 2007 Chevrolet Impala With a Trunk Mounted Bike Carrier
  You would not want to open the trunk while a trunk mounted bike rack is installed on your 2007 Chevrolet Impala because it could cause damage to the vehicle. If you would like to have access to your trunk without having to remove the bike rack every time, then I would recommend adding a hitch and hitch mounted bike rack. For your vehicle, I would recommend the Draw-Tite Class II Hitch, # 36407. There will be no contact between your vehicle and a hitch mounted bike rack and you will be...
  view full answer...
• Malfunction Turn Signal Light on Sunline Travel Trailer
  The first step would be to check the wiring from the malfunctioning light all the way up to the connector. Make sure all the connections are reasonably clean and secure, and check for frayed wires. If everything looks good from there, I would begin to look at the tow vehicle wiring. Check to make sure your connections are clean and secure. We have a few handy devices that could help you check all this. You could use a circuit tester like part # PTW2993 to check to see what connections...
  view full answer...
• Is Trailer Hitch For 2008 Chevrolet Impala Guaranteed To Fit
  The trailer hitches we offer for your 2008 Impala are guaranteed to fit. These hitches are designed specifically to fit your car frame. The trailer hitch you came from is the Curt, part # C12252. This is a Class ll hitch and it has a 1-1/4 inch receiver opening. The other trailer hitch is the Draw-Tite, part # 36407. This is also a Class ll hitch with a 1-1/4 inch receiver. I recommend the Draw-Tite hitch because it does not require a stabilizing strap like part # 18050 for all non-trailer...
  view full answer...

Do you have a question about this Custom Fit Vehicle Wiring?