Expert Answers about Mazda 3

• Why Are Curts Measurements Different Than What Is Listed?
• We measure rise and drop a little differently than Curt, hence the discrepancies with the label on their # C45028. Curt tends to round and estimate their measurements a little bit, but we go from the top of the ball platform to the top of the shank to get the 5-3/8" rise. This goes for the drop measurement as well, just with the ball mount flipped over. I included a review video we have of this showing where we take the measurements from as well.
  view full answer...


• Would the Exhaust of a 2016 Mazda 3 Melt Bike Tires when Using Swagman XC S64650
• The distance from the hitch pin hole of the Swagman bike rack part # S64650 to the nearest wheel hoop is 10-1/2 inches. The shank of this rack also has a rise of 4 inches built into it. The tires of your bikes would be far enough away from the exhaust that you wouldn't have any problems. With this bike rack we have not had any issues with exhaust so I can confidently say you will be fine. If you do not have a hitch already you would want the Draw-Tite part # 24914 which has been confirmed...
  view full answer...


• Roof Rack for 2013 Mazda 3 Five Door to Carry a Rowing Shell
• The most cost effective and aerodynamic (thus quiet) roof rack would be a Rhino Rack system, that would consist of the following: 44 inch Silver Vortex Aero Crossbars # RRVA118S-2 (also available in black as # RRVA118B-2) Leg Kit # RRRLKVA Vehicle Specific Fit Kit for vehicles with fixed roof mounted attachment points, # DK289 The rack would be easily removable when needed. Rather than resting your rowing shell directly on the crossbars, I'd recommend using a foam block system like the...
  view full answer...


• Will Wiring Harness 118420 Fit a 2006 Mazda 3 Grand Touring
• My contact at TowReady confirmed that the 2006 Mazda 3 Grand Touring models have differently shaped connectors than the standard models, so the # 118420 wiring harness would not be able to be installed on your vehicle. I recommend using taillight converter # C56175 to wire your vehicle for towing. I have included a link to the installation instructions for the converter.
  view full answer...


• Which Snow Chains for a 2010 Mazda 3
• Your Mazda 3, if equipped with the factory wheels and tires, you can use either the Thule CB12 Size 090 chains, part # TH01221090 or the Thule K-Summit Chains part # TH02230K23. The K-Summit Chains are the easiest and quickest chains to install. The CS10 chains are self-tensioning so unlike basic sets, these chains will tighten themselves. They take more time to install, but they are less expensive when compared to the K-Summit chains.
  view full answer...


• Fit of Curt C98BR Class I Hitch on 2021 Mazda 3 Turbo Hatchback
• The Draw-Tite Class I hitch, part # 24984 is a fit for all models of the 2021 Mazda 3 according to Draw-Tite. Usually, the on the more sporty models of small cars, the dual exhaust can present a fit problem, but as you can see in the linked installation instructions as well as the provided photo, the hitch fits perfectly with a dual-exhaust equipped vehicle. The receiver tube is hard to see, so I've circled it in red. If you'll be using the hitch for light duty towing, you'll also need...
  view full answer...


• Is Stabilizer Strap Needed for Bike Rack with Curt Class I # C11393 on 2011 Mazda 3 Sedan
• The provisions of the Curt Class I # C11393 hitch warranty requires the use of a stabilizing strap like part # 18050 for non-trailer loads like a cargo carrier or bike rack. Keep in mind, the hitch manufacturers punch a stop into the receiver tube of a Class I hitch that will prevent the shank of Class II accessory from being used. This is done because a Class I hitch has a limited tongue weight capacity (maximum amount of weight that can be safely suspended from the receiver) when compared...
  view full answer...


• Recommended Trailer Hitch and Bike Rack for 2020 Mazda 3 Hatchback
• Absolutely! Starting with the trailer hitch for your 2020 Mazda 3 Hatchback, the Curt Hitch # C98BR will work perfectly. This will line right up to existing holes in the frame rails for a simple bolt-on (no-drill) installation and features a 200 pound tongue weight capacity. I have attached the written installation manual below that you can look through as well. All the necessary hardware is included. Then for a Class I rated bike rack I highly recommend the Kuat Transfer V2 # KU74FR....
  view full answer...


• How to Remove the Fishwire Tool From Bolts When Installing Hitch on 2008 Mazda 3
• When using the included fishwire tool, also known as a bolt leader, when installing a trailer hitch like the Curt Trailer Hitch # C11386 that fits a 2008 Mazda 3, the bolt leader will simply thread on and off the bolts. There isn't a trick to it, per se, and trying to remove it from the bolt should not have made it grip tighter (though I do appreciate your analogy to "novelty finger handcuffs") unless you were also pulling on it at the same time. I can't say for sure why this may have...
  view full answer...


• Recommended Trailer Hitch Receiver for 2016 Mazda 3 Hatchback GT Sport
• I suggest the Draw-Tite Sportframe # 24914 for your 2016 Mazda 3 Hatchback. The Curt # C11377 that is available to fit requires the use of a support strap when carrying non-trailer accessories on the hitch. The Draw-Tite doesn't have this requirement. For a ball mount you can use the # 3593 which includes a pin and clip. A 2 inch hitch ball to fit is # 19258 and a 1-7/8 ball is # 19256. You'll also likely need trailer wiring to power your trailer's lights. The wiring harness # 119178KIT...
  view full answer...


• Tongue Weight Capacity of EcoHitch 306-X7305
• The tongue weight capacity of the EcoHitch # 306-X7305 for a 2015 Mazda 3 is indeed 300 lbs. After we wrote the original product description, EcoHitch did further weight capacity testing on the # 306-X7305 hitch and found that it had a higher tongue weight capacity than originally stated. The hitch will work great with your Mazda 3 and your 2 inch bike rack.
  view full answer...


• Transmission Cooler for a 2017 Mazda 3 with the 2.0L I4 Engine
• There are three different style's of transmission coolers; remote mount, standard mount, and pan mount. The most common cooler we have is a standard mount cooler that will need to be positioned on the front of the vehicle where airflow is sufficient. A remote mounted transmission cooler can be located anywhere on the vehicle as the included fan will ensure the proper amount of airflow is received. The last type of transmission cooler we offer is a pan mounted cooler which replaces your...
  view full answer...


• Difference between C113833 and C11383 For a 2012 Mazda Speed3
• You are correct, the only difference between the Curt Hitch # C113833 and the Curt Hitch # C11383 is that the # C113833 comes with a ball mount and the # C11383 does not. Either of these hitches would work well for you as long as you have a hatchback, if you have a sedan you would want a # C11393 or a # C113933 if you want a ball mount as well. You may also be interested in the following products to complete your towing setup also: Tow Ready Wiring Harness # 118420 (instructions and...
  view full answer...


• How Much Does the 20x47 Reese Cargo Carrier Part # 63155 Weigh
• The 20x47 Reese Cargo Carrier part # 63155 weighs 44 lbs. This carrier is rated class I and class II. The Draw-Tite Sportframe Trailer Hitch Receiver part # 24843 is a class I hitch so it will work. You should not exceed 156 pounds of cargo.
  view full answer...


• Ratchet Strap Solution for Yakima Offgrid Roof Cargo Basket
• I wish we did but we don't have any anchor points that can attach to the round bars that are on top of the Yakima OffGrid Roof Cargo Basket # Y07138-08 so you might look into a ratchet strap setup that you could wrap around the entire basket and hook back to the opposite hook of the strap like the # 34414.
  view full answer...


• How To Tell If Lights On 2015 Mazda 3 Are LED Or Incandescent
• You can find out if you have LEDs a couple of ways. The easiest is to remove the lens of the lights and if it has a bulb it is incandescent. If it has diodes then it is LED. Another way is to turn the lights on and then watch as you turn them off. If the light go off abruptly, they are probably LED. If the filament takes a moment to go out then it is probably a bulb. The third way is to contact your dealer with the VIN and they will be able to tell you what lights are on your Mazda 3.
  view full answer...


• Will the SportRack Vista XL Cargo Box Work on a 2007 Mazda 3 5door with a Thule Square Load Bars
• Yes, this Sportrack Vista XL Cargo Box # SR7018 will work on Thule Square Load Bars # THLB50 like what you have on your vehicle. This cargo box has a capacity of 100 lbs, you will also need to know the weight capacities of the rack you have on your vehicle as well as the capacity that the roof of your vehicle has and then go with the lowest rated component as your overall weight capacity.
  view full answer...


• Do I Need To Use Support Strap To Carry Bike Rack w/ Draw-Tite Trailer Hitch # 24843 on 2011 Mazda 3
• CURT is the only hitch manufacturer that requires that you use a support strap like the CURT Bike Rack Strap, part # 18050, when carrying a bike rack using their hitch. The Draw-Tite Trailer Hitch # 24843, would be a great option for a hitch on your 2011 Mazda 3 w/o LED tail lights. All of the hitches we carry are of quality, including Draw-Tite. One reason why the other hitches have a higher price point is that they include a ball mount, pin and clip. The Draw-Tite # 24843 does not include...
  view full answer...


• Curt 4-Pole Wiring Installation and Mounting Bracket for 2013 Mazda 3
• Curt 4-pole wiring harness # C56011 does include a protective cap for its connector. This helps prevent entry of moisture and contaminants that can lead to corrosion. But if you have periods of no towing during the winter you can simply remove the plug from its mounting bracket and keep it inside the vehicle. This is why in the linked video our installer shows how to route the 4-pole wire out the rear hatch when it is going to be needed. For a bracket the part # 18144 which is a universal...
  view full answer...


• Recommended Method To Tow 2007 Mazda 3 Behind Motorhome
• I may have an option for you, but while researching flat towing I found that the owner's manual for your 2007 Mazda 3 mentions that your vehicle should not be flat towed. With that being said Blue Ox does offer a base plate kit for your vehicle leading me to believe that there are modifications that can be made to allow you to flat tow your vehicle but I was unable to find out exactly what may need to be done. If you choose to go the flat tow route you will need the Blue Ox Base Plate...
  view full answer...