I have a great solution for you. At eTrailer, we strongly recommend against using wheel-mount bike racks for bikes with fenders. There is no way to guarantee that the ratcheting hooks can secure the bike by the wheels at a 3-o'clock position on the Saris SuperClamp EX Bike Rack for 2 Bikes # SA4025F. In addition, we strongly discourage mounting a bike by any attached cargo carriers over the bike's wheels.
A great alternative bike rack that avoids these problems is the Swagman E-Spec Bike... view full answer...
The cutout on your frame is different from what we have seen. It does appear to be smaller. You'd want to use a dremel or rotary tool to enlarge it slightly till you can pass the bolt and spacer of the Curt Hitch part # C11377 through. view full answer...
The Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4" # C11390 you asked this question from is a confirmed fit for your 2012 Ford Fusion. It absolutely is possible to spread an installation out over two days, but you will want to be careful of a couple of things.
Once you have the bolts installed into the frame, you will want to make sure that they can't vibrate loose from their location. This may mean using additional washers to ensure the flange lock nut doesn't have the... view full answer...
There are two holes on the side of your frame underneath the tape of your 2019 Mazda 3. You might double check to make sure you checked the correct one as it's pretty easy to mistake the wrong one. I attached a picture that shows which slot to use. view full answer...
Removing the Rhino-Rack ROC23 Roof Rack, part # RR54GR, from your 2012 Mazda 3 is not terribly difficult. However, it will require you to uninstall it. That is to say, the installation process and the process of uninstalling are the same. The good news is that the installation is fairly easy. The instructions are linked below. view full answer...
According to the installation instructions for the Draw-Tite Class I hitch, # 24914, you will not have to alter the bumper on your 2015 Mazda 3.
The hitch will bolt to already existing holes in your car's frame. No welding or drilling will be required.
The instructions do say that you will have to temporarily lower the exhaust during installation.
The installation instruction are linked toward the bottom of this page for you to review. view full answer...
Though I can confirm the EcoHitch # 306-X7303 will absolutely fit a 2016 Mazda 3, we have yet to do an install with said hitch. However, we do have an install we did with a Draw-Tite # 24912 on a 2015 Mazda 3. There will be a few subtle differences, but they do attach the same way. I included that video for you to take a look at. view full answer...
If you install any roof rack on your 2012 Mazda 3, you can remove it if needed, even if that rack attaches to the fixed points on the vehicle.
The fixed points for the rack are located under small plates that you can just pull up and off of the vehicle like in the video I have linked on a similar vehicle. In some cases a small flat head screwdriver can be used to gently pull the covers up.
For the Thule roof rack you would need the following parts:
SquareBars: # TH712200
Podium Foot... view full answer...
The yellow, brown, and red refers to the wires on harness # 118420 for your 2012 Mazda 3 sedan. The wire colors used on the vehicle will not likely be these colors because there isn't a standard color code for automotive wiring.
You will just need to locate the matching connectors on the driver's side that will accept the connectors with the red, brown, and yellow wires. The green wire and its connectors plug in line with the passenger's side tail light wiring. I have linked a video that... view full answer...
Yes, to install the Draw-Tite Sportframe Trailer Hitch Receiver # 24984 on your 2023 Mazda 3 you will need to remove that panel and it won't be put back into place.
Hitch instructions only mention this when the hitch either prevents the panel fitting back into place or there is excessive trimming that needs to be done on the panel for it to fit back in place so it's easier to just remove it and leave it off.
If you'll be using the hitch for towing I recommend installing the T-One Wiring... view full answer...
When using the included fishwire tool, also known as a bolt leader, when installing a trailer hitch like the Curt Trailer Hitch # C11386 that fits a 2008 Mazda 3, the bolt leader will simply thread on and off the bolts. There isn't a trick to it, per se, and trying to remove it from the bolt should not have made it grip tighter (though I do appreciate your analogy to "novelty finger handcuffs") unless you were also pulling on it at the same time.
I can't say for sure why this may have... view full answer...
The Kat's heater part # KH11409 plugs into one of the freeze plugs in the back of the engine block. There should be a couple different options to use, but use the rear most hole. It is recommended to use a certified mechanic for install. When installing it, you need to drain all of the coolant from your radiator, submerge the heater in coolant before energizing it, then you can install the block heater. You need to use a 50/50 blend of coolant and distilled water. I am going to attach a... view full answer...
There is no cutting or trimming of the rear fascia/bumper of your 2014 Mazda 3 required to install the Draw Tite hitch part # 24912. To see more install info check out the installation instructions I attached to the right.
In the unlikely event of you having to replace the muffler of your vehicle you would not have to remove this hitch. view full answer...
The RhinoRack roof rack system for your 2010 Mazda 3 4-door sedan, consisting of parts # RRVA118B-2, # RRRLKVA and # DK289, uses clamp assemblies (part # RRRLKVA) that do grab onto the door jambs on the vehicle. This component also includes locks to secure the rack to your roof.
Optional locking end caps are offered for the Vortex Aero crossbars, part # RRVA-LEC4, to secure cargo carriers and other accessories to your crossbars.
Before loading anything on your roof rack it is suggested... view full answer...
When a trailer hitch is constructed, the manufacturers use a more malleable steel to construct the mounting flanges than what's used in the crossbar and receiver tube. This allows the hitch to flex a little bit along with the vehicle. Because of this flexibility, the mounting flanges can and do sometimes get slightly bent out of alignment during the shipping and handling process. This is very easy to fix, the procedure is outlined in the help article I've linked for you. view full answer...
We do not yet have an actual photo of the hitch on a 2008 Mazda 3. The installation instructions include a nice diagram on how the hitch will fit in relation to the bumper, and I have provided a link to those below. The existing holes for installation need to be enlarged so may be hard to see underneath the vehicle if you do not know exactly where to look. view full answer...
The Thule FastRide Roof Bike Rack # TH95JV is a great option for your 2020 Mazda 3 and will install by using either the clamps for standard crossbars or the T-Slot hardware if your crossbars have the T-Slot on the top.
Attached is a review video where we show how to install this for you to check out. view full answer...
In order to tow a trailer with a 2022 Mazda 3 Sedan you'll need a trailer hitch, the Draw-Tite Sportframe Trailer Hitch Receiver part # 24982 is what I recommend. This hitch offers an easy bolt-on install with no drilling required. In order to complete your setup you'll also need a trailer wiring harness, the T-One Vehicle Wiring Harness part # 118808 is what I recommend. Finally, you'll need a ball mount/hitch ball, the Draw-Tite Drawbar part # 3593 with 1-7/8" Hitch Ball part # 19256... view full answer...
I apologize for the issue you had with the installation instruction link for the Draw Tite Hitch # 24816 that you purchased. I attached a picture to the right (it might take till tomorrow morning for it to show up) that has the installation instructions.
I also attached the install video you referenced. view full answer...
Thanks for reaching out!
When you installed the pewag Servo RS Self-Tensioning Snow Tire Chains # PWRS74 on your 2022 Mazda 3 215/45R18 tires did you loosen up the self-tensioning device? If you check out the 7:00 minute mark of the linked video you'll see where we press a button to provide a LOT of slack to make that final connection. Once that connection is made then you'll press the button to activate the self-tensioning feature.
Your tire size if one of the largest fits for this chain... view full answer...
Go To Results