Availability Of A Drill Adapter For The TJD-12000SP-R2NH Square Jack

Question

Question:

Is there a adapter to attach a drill or impact to raise and lower the leg for this?

asked by: Ron

0

Expert Reply:

Unfortunately we do not offer a drill adapter for the square jack # TJD-12000SP-R2NH. The only way to raise and lower the jack will be with the manual crank handle # TJD-12000-HD. Bulldog used to make a powered drive kit that worked with these jacks, but that has not been available for quite some time.

expert reply by: Jesse M

0

Answer 1

I spoke with my contact at Ultra-Fab about the Power Twin II Electric Stabilizer, part #UF39-941705. They recommend not using this system because of the movement any livestock would make in the trailer. They said any movement would cause additional…

view full answer...

Answer 2

The handle that you need for the Square Direct Weld Jack - Drop Leg w/ Spring Return part #TJD-12000SP-R2NH is part #TJD-12000-HD. This handle replaces the handle on all of the TJD-12000 Series square jacks. It comes with the bolt and hardware…

view full answer...

Answer 3

To use the 25K etrailer Square Gooseneck Companion Jack #TJD-25100 at the front of your TopHat trailer you just need the following parts: - Connecting Rod #LG-XTB - Sidewind Crank #TJD-12000-HD We don't have a bracket for the connecting rod…

view full answer...

Answer 4

The only difference between the two landing gear sets you referenced is that Landing Gear #RVLG-8HDL comes with a handle and #RVLG-8000 does not. Apart from that they are the exact same landing gear sets, with 20-1/2" of travel, an 8,000 lb…

view full answer...

Answer 5

Ultra-Fab T-Slot Power Drill Adapter #UF48-979071 is designed for use with Ultra-Fab scissor jack applications but is not confirmed to work with landing gear. You would have to go by the measurements. The inner diameter of the hole is 0.66 inches and…

view full answer...

Answer 6

Send me the pictures you have and I'll see if it's something we can get.

view full answer...

Answer 7

Good news! I was able to get a exploded diagram as well as a set of instructions on how to replace the rod and gears #TJD-12000-RODNUT in the #12000 Series Ram Jacks made after 2012. I have attached them to this page for your convenience. Basically,…

view full answer...

Answer 8

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 9

Assuming your Sprinter has the factory tow package with the 7-way at the rear bumper, in addition to the #RED24FR Redarc Tow-Pro Liberty Brake Controller, you'll also need the #3063-P wiring harness and the #331-TPH-017. The connector to install…

view full answer...

Answer 10

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 11

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...