Replacement Parts for etrailer Square Direct Weld Jack

Question

Question:

Bought a used trailer believe it has the TJD-12000SP-R2NH Jack which stopped working. The threads in the part that bolts to the top of the inner leg and the screw twists through have been stripped out. Can I get that bolt in piece?

asked by: Jeff

0

Expert Reply:

It sounds like you're talking about the rod and nut on the # TJD-12000SP-R2NH. We have the following replacement parts available:

-Replacement Rod and Nut for etrailer and Ram Square, Direct Weld Jacks # TJD-12000-RODNUT

-Replacement Sidewind Gear Kit for etrailer and Ram Square, Direct Weld Jacks # TJD-12000-GR

-Replacement Return Spring for etrailer and Ram Square, Direct Weld Jacks # TJD-12000-RSP

-Replacement Bearing for etrailer and Ram Square Jacks # TJD-12000-BR

-Replacement Square, Direct Weld Jack Inner Tube with Spring-Return Drop Leg # TJD-12000SP-FIP

-Replacement Cap # TJD-12000-CP

If it is not the rod and nut, or one of the other replacement parts, feel free to send me a picture and I'll see if it is something we are able to get a replacement for. I have attached a video below which covers the rebuild process for your reference.

expert reply by: Robin H

0

Answer 1

The return springs in landing gear jacks are not replaceable or repairable unfortunately so if you have the #TJD-12000SP-R2NH.

view full answer...

Answer 2

If you look at the backs of the brake assemblies there should be a hole where the magnet wires come out and a little opaque plastic strap. So if you are looking at the back of the assembly and those items are on the left then it is the left side…

view full answer...

Answer 3

Good news! I was able to get a exploded diagram as well as a set of instructions on how to replace the rod and gears #TJD-12000-RODNUT in the #12000 Series Ram Jacks made after 2012. I have attached them to this page for your convenience. Basically,…

view full answer...

Answer 4

Connection three 10-gauge wires together is going to be best accomplished by soldering the connections as this is the most secure method. We have a solder gun that comes with solder as well with part #PTW2012. I realize that not everyone knows how to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The torque specs for 9/16" diameter u-bolts like the U-Bolt Kit for Mounting 5,200-lb to 7,000-lb, Round Trailer Axles part #APUBR-9 will be a range, from 65 ft. lbs. to 95 ft. lbs. If the tie-plates start to bend inside this range that would be…

view full answer...

Answer 7

The replacement parts we have for the Bulldog Square Jack #BD182500 are a Replacement Gear Kit #BD500212 and a Replacement Screw and Nut Kit #BD500217. These are the two most likely aspects of the jack to be causing your problem. I have attached the…

view full answer...

Answer 8

The spring that comes with gear set #BD500212 for Bulldog 12K jacks is a compression spring. It keeps tension on the upper gear to help keep in place and aligned. I have included a picture that shows where the inner pieces go inside the jack.

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...