Curt Ball Mount for 2" Hitches - 2" Rise, 4" Drop - 8-1/4" Long - 7,500 lbs

See what our Experts say about this CURT Trailer Hitch Ball Mount

• Wiring Needed to Tow Travel Trailer With Brakes With 2016 Toyota Highlander
  We can certainly assist you with getting your 2016 Highlander geared up for towing your new travel trailer. Let's begin with the hitch, if you don't already have one. I'd recommend the Curt # C13200 which is a confirmed fit unless your Highlander has a spare tire that's mounted on an aluminum rim. You'll also need a ball mount like # C93KR a hitch pin like # PC3 and a trailer ball like # 19260 for a 1-7/8 or # 63845 for a 2 inch diameter ball. For a trailer wiring harness, since you're...
  view full answer...
• 2016 Toyota Highlander Limited Platinum Trailer Wiring Harness
  We really dislike the term 'tow package' here at the etrailer.com World Headquarters, because the term basically has no meaning. In most folk's mind, saying something has the tow package would indicate the the vehicle rolled out of the factory and was completely equipped to tow which would be the case in a perfect world. But alas, that's not the case. In terms of which 4-pole trailer connector harness you need for your Highlander, there's a super-easy way to tell. Pull out the cargo tray...
  view full answer...
  
• Ball Mount With 2 Inch Rise For 2018 Subaru Crosstrek & EcoHitch Trailer Hitch Receiver
  We can definitely get you set up with a ball mount that is properly rated for your towing needs as well as the EcoHitch Stealth Trailer Hitch Receiver # 306-X7365. I'll go ahead and list out the ball mount and other parts you'll need for this: - Curt Ball Mount for 2" Hitches - 2" Rise or 4" Drop # C93KR - Pin and Clip # C21500 or Trailer Hitch Receiver Lock # e98880 - 1-7/8" Hitch Ball # C40002 or 2" Hitch Ball # 63845 Each of these parts is rated properly, with the ball mount having...
  view full answer...
• Hitch and Wiring Recommendations for a 2011 Honda Odyssey
  I definitely recommend going with a 2 inch receiver, like the etrailer.com # e98862. This will have a higher towing capacity than the 1 1/4 hitches and also gives you more options for accessories like bike racks or cargo carriers. Whereas the hitch refers to the vehicle, the 2 inch coupler refers to the trailer. This is a fairly standard size coupler and will utilize a 2 inch ball like # C40004 that would be installed on a ball mount like the Curt # C93KR, which would then be installed...
  view full answer...
• Sway Control Bar For Two Tow Vehicles
  Unfortunately ou will not be able to use a sway bar with an adjustable height hitch. Typically we would recommend the Curt # D320 ball mount with the sway control tab already welded in place. This ball mount will provide 2" of drop. (For more information about ball mount drop or rise see the attached article.) Then on the trailer tongue side you install the Curt # 17200 Friction Sway Control System. Note that the system includes the tiny hitch ball that installs on the tab of the # D320...
  view full answer...
• What Equipment Do I Need to Tow a Trailer with My 2022 Hyundai Sante Fe?
  For towing a trailer on your 2022 Hyundai Sante Fe, the first thing you need is a trailer hitch installed on the vehicle. I recommend the Curt Trailer Hitch Receiver - Custom Fit # C34ER because it will give your vehicle a maximum gross trailer weight capacity of 4,000 pounds at a competitive price. However, I recommend that you consult with your vehicle's owner's manual to make sure that you don't exceed the tow rating of your Sante Fe. If you need assistance with installation, the attached...
  view full answer...
• Smallest Diameter Shank For 2-5/16" Trailer Hitch Ball
  The smallest diameter shank for a 2-5/16" hitch ball is a 1" shank like for the 2-5/16" Hitch Ball # C40007. Hitch balls with 3/4" diameter shanks are all either 2" or 1-7/8" hitch balls, so if you need to use a 2-5/16" hitch ball and your ball mount has a 3/4" diameter shank you'll need a new ball mount to go with the # C40007, like the Curt Ball Mount for 2" Hitches - 2" Rise, 4" Drop. # C93KR. That depends on the rise or drop you need, so I've added a link below to our entire selection...
  view full answer...
• Can Curt Rockerball be Used in Curt Ball Mount # C93KR
  Yes, the Curt ball mount part # C93KR is compatible with Rockerballs like the part # C82KR that you mentioned.
  view full answer...
• Hitch for Small Truck
  I have several hitches that closely match what you are looking for. Hitches I have that fit a 2"X2" receiver opening, and with 4" drop are as follows. Curt # C45055, 8-1/4" hitch pin center to ball mount center. Overall length is 12-1/2" Curt # C93KR, 8-1/4" hitch pin center to ball mount center. Draw-Tite # 40331, 9-3/4" from hitch pin center to ball mount center Curt # C45313, 10" from hitch pin center to ball mount center Draw-Tite # 4285, 12" hitch pin center to ball mount center....
  view full answer...
• Rockerball With Forged Mount and Sway Control
  The Curt RockerBalls # C82KR are not to be used with sway control. The 2 systems will fight against each other as you are driving. They also will not fit the Curt Forged Ball Mounts # C45341. They require the 2-1/2" wide ball mount for the anti-rotation base that keeps the RockerBall aligned properly. Also the bolt hole must be within 1/16" of the 1" ball threaded shaft. I recommend Curt Ball Mount # C93KR due to the added height of the RockerBall. This will work if your current ball...
  view full answer...
• What Ball Mount Comes with Curt Rockerball Ball Mount Kit with 3 inch Drop C63KR
  The ball mount that comes with the # C63KR has a 3 inch drop but since you already have the ball all you'd need is the ball mount of the kit which would be part # C93KR. The Rockerball is not available with a 50 mm ball size.
  view full answer...
• Availability of 5 Inch Drop Ballmount With Preinstalled 2 Inch Trailer Ball
  We don't offer a 5 inch drop ball mount, but if you were to use a 4 inch drop like part # C93KR and installed a # 63845 ball, you'll get a bit of squat in the rear suspension of the vehicle (which would vary according to the trailer's tongue weight) that would put you close enough to the 5 inch drop you're looking for. The ball needs to be torqued to 250 foot lbs, but any local shop should be able to do that for you without charging you an arm and a leg. The trailer doesn't need to be...
  view full answer...
• Trailer Hitch and Towing Accessory Recommendation for 2014 Infiniti QX60
  We do have hitches that will work for your 2014 Infiniti QX60, but the # 76034 you specified is a fit for the Ford Explorer, and wouldn't fit your Infiniti. Not only are the frame members at a different width, but the mounting holes are all different and wouldn't match up. For your QX60, I'd recommend the Curt Class III, part # C13126. This is a mainly concealed installation, which means that the only visible portion of the hitch will be the receiver tube and the safety chain hoops. If...
  view full answer...

Do you have a question about this Trailer Hitch Ball Mount?