Pigtail Wiring Harness for Tekonsha and Draw-Tite Brake Controllers - 60" Long

See what our Experts say about this Tekonsha Accessories and Parts

• Is There a Way To Extend The Wiring Adapter # 3073-P For a Tekonsha Trailer Brake Controller?
  While Tekonsha does not have a plug and play extension you can cut the included end off of the Adapter # 3073-P and extend it 34" # 7894 or 60" # 20160 with one of their universal pig tails. If you only need a short amount you may be able to use the pigtail which came with the Prodigy P2 # 90885 should you still have it handy. We do offer some Wire Loom # 7509-1 which is sold by the foot if you want to clean up the extended wiring.
  view full answer...
• Transferring Tekonsha Brake Controller From 2005 Chevy Tahoe to 2015 Chevy Suburban
  Your 2005 Chevy Tahoe uses adapter # 3015-P to install the Primus IQ, part # TK90160. If the 2015 Chevy Suburban has a factory 7-way at the rear then it uses part # 3016 to install the controller and this is all you need. If the Suburban doesn't have a factory 7-way the wires to install a controller are under the dash but there isn't a connector to just plug it into. You need to start by adding a 7-way using part # 30955. Then hardwire in the Primus IQ using adapter # 20160.
  view full answer...
• Can Draw-Tite Activator IV Trailer Brake Controller 5504 Be Installed In 2020 Ford Ranger W/ Tow PKG
  Yes. The Tekonsha BRAKE-EVN # TK63VR you were looking at will work just fine on your 2020 Ford Ranger with the factory tow package. You will need the Pigtail Wiring Harness for Tekonsha and Draw-Tite Brake Controllers # 20160 to connect to the factory wires you located underneath the dash of your truck. In addition you will need a circuit tester like # PTW2993 to confirm the functions of the factory wires and match the functions to the # 20160 which are as follows: Black wire is 12v...
  view full answer...
• Do You Have To Setup the Tekonsha Primus IQ Again If You Unplug It
  If you unplug a wired trailer brake controller like the Tekonsha Primus IQ Trailer Brake Controller part # TK90160 you'll need to go through the setup procedure again and you will lose all your settings. The Curt Echo Wireless Trailer Brake Controller part # C51180 is something you can unplug and not lose any saved setting but that's all that I am aware of with this feature. In regards to an extension harness, I am aware of hardwire options like part # 20160 but none that are custom plug-in-play....
  view full answer...
• Recommended Brake Controller and Wiring for 2000 Toyota 4Runner and 2017 Subaru for 2004 Aliner
  For your 2000 Toyota 4Runner as well as your 2017 Subaru Outback, you will need to use a hardwired connection for your brake controller. There is a simple way to use the wiring you suggested to connect to your 4-way flat adapter and give you the options you desire. I recommend the Hopkins Endurance Multi-Tow 4-Way Flat to 7-Way RV Trailer Adapter w/ 4-Way Vehicle End Plug # HM47180. This will connect to your existing 4-way and then you will need to run wires for the 12V power (charge)...
  view full answer...
• Can The Tekonsha P2 Trailer Brake Controller Be Mouned on Top of Dash Rather Than Down Low?
  Yes, the Tekonsha Prodigy P2 Trailer Brake Controller # 90885 can be mounted on top of the dash on your 2017 Nissan Pathfinder LT, with the factory tow package. This is quite common on several vehicles which actually place the factory connector behind a panel in the dash rather than behind the drivers area of the dash. Running the Tekonsha Plug-In Wiring Adapter # 3050-P would be rather difficult. Instead you could use either the 34" Pigtail # 7894 or 60" Pigtail # 20160 and then attach...
  view full answer...
• Recommended Mounting Location for Tekonsha Prodigy P2 in 2022 Nissan Frontier
  Looking at pictures of the 2022 Nissan Frontier interior, the best mounting location for your P2 # 90885 is probably to the right of the steering wheel under the dash. The only other spot I could see it going is to the left instead. As you said, space is limited. If you want to run it to the passenger side you can use the # 20160 but that would require splicing. Also, you would want to make sure it isn't so far that you can't easily adjust or use the manual override.
  view full answer...

Do you have a question about this Accessories and Part?