Undercover Access Hole Cover for EcoHitch Stealth Trailer Hitch Receiver

See what our Experts say about this EcoHitch Accessories and Parts

• Undercover Access Hole Cover for EcoHitch Stealth Trailer Hitch Receiver Template
  For the EcoHitch Access Hole Cover # 306-XA2002 here are the instructions on how and where to drill access hole: Place the bumper on the ground to allow marking on the inside floor of the plastic undercover with ribs. Measure from the front of the plastic 26-3/4 inches along the center rib, if using a 3-1/2 inch hole saw. More hand clearance is possible if using a 4-inch hole saw but measure 26-1/2 inches. Mark two points to use as start holes. Mark 3/4 inch from the center towards...
  view full answer...
• Dimensions of Undercover Access Hole Cover for EcoHitch Stealth Trailer Hitch
  The dimensions of the Undercover Access Hole Cover for EcoHitch Stealth Trailer Hitch Receiver # 306-XA2002 that you referenced is 8-1/2" long by 5-1/16" wide by 1/8" thick. Your hole being initially cut with a 4 inch hole saw would not be too large to work with this.
  view full answer...
  
• Replacement Undercover Access Hole Cover for EcoHitch Stealth Trailer Hitch
  It sounds like you are looking for the Undercover Access Hole Cover for EcoHitch Stealth Trailer Hitch item # 306-XA2002. I have attached a picture below so you can confirm that this is the part you need.
  view full answer...
  
• Installing EcoHitch Stealth Receiver # EH84GR on 2018 Tesla Model 3
  I see exactly what you are referring to with regards to the plates that need to be removed on the Tesla Model 3 when installing the EcoHitch # EH84GR. There is no need to worry though about rust or corrosion in that area because the mounting brackets for the hitch will essentially be taking their place. Using the included nylon washers and bolts the hitch brackets will create a tight seal at that location to prevent anything from creeping in between them and the frame. Once the hitch is...
  view full answer...
• Can Hole Cut in 2020 Tesla Model 3 be Covered When Not In Use
  A hole does get cut in the lower fascia of your 2020 Tesla Model 3 to install the EcoHitch # 306-X7373 but we offer a cover for the hole that you can use when the hitch isn't in use. For that you'd just need the part # 306-XA2002. I attached a picture of what it looks like installed for you to check out as well. I attached an install video for the hitch and a review video for the cover for you to check out as well.
  view full answer...
  
• Part Needed to Cover Access Door for Eco Hitch Installation on Tesla Model 3
  You can use the Undercover Access Hole Cover for EcoHitch Stealth Trailer Hitch Receiver # 306-XA2002, which will keep your access hole covered. This is a magnetic piece that attaches to the hitch and keeps the inside area free from road grime and dirt. I've linked a short review video of this part for you to check out.
  view full answer...
• Recommendation for a Concealed Trailer Hitch on a 2021 Tesla Model 3
  We have exactly what you are looking for, two options, each from Stealth Hitch. The first option is the Stealth Hitches Hidden Rack Receiver, # 391TES317. This fits a 2" hitch and is a completely hidden hitch that keeps your Tesla Model 3 looking just like it was when built, no "ugly" hitch sticking out the back. You can easily remove the receiver portion of the hitch separating it from the concealed crosstube that remains hidden. This will provide you with a 2" x 2" receiver opening...
  view full answer...
  
• What Can I Do To Cover The Hole In The Lower Fascia Of My 2022 Tesla Model 3 With Stealth Hitch
  Yes, that is definitely something that can be covered. The Stealth Hitches Hidden Rack Receiver - Custom Fit - 2", part # 391TES317, you installed on your 2022 Tesla Model 3, leaves a hole in your vehicle's lower fascia after installation. This can be taken care of with the Undercover Access Hole Cover for EcoHitch Stealth Trailer Hitch Receiver, part # 306-XA2002. This attaches to your Stealth Hitch via a magnet. It comes equipped seals to keep this cover in place. I have included product...
  view full answer...
• Cover For Hitch Access Hole In 2020 Tesla Model 3 Fascia.
  The Undercover Access Hole Cover for EcoHitch Stealth Trailer Hitch Receiver # 306-XA2002 will be able to cover the access hole for your stealth hitch on your 2020 Tesla Model 3. I have linked some videos to help you see the product.
  view full answer...
• Is EcoHitch Undercover Access Hole Cover Needed for 2019 Tesla Model 3
  The access hole cover, part # 306-XA2002, isn't needed for all of the 2019 Tesla Model 3 so look under your car before getting it. Some of the 2019 models have a cover installed right from the factory.
  view full answer...
  
• How To Protect Debris From Entering EcoHitch Stealth Hitch With Receiver Tube Installed
  It sounds like you are asking about the EcoHitch Stealth Trailer Hitch Receiver part # EH84GR which is a fit for your 2019 Tesla Model 3. If that is the case then the Undercover Access Hole Cover part # 306-XA2002 will be used when the receiver tube is removed but if you were to leave the receiver tube installed you could then use the Rubber Hitch Cover for 2" Trailer Hitches part # 22282 to protect from dirt and debris.
  view full answer...
• Is 2023 Tesla Model 3 TorkLift Wiring The Same as ZCI Wiring Kit
  From what I'm seeing it does look like the TorkLift TY2020 wiring kit is the same as our ZCI Circuit Protected Vehicle Wiring Harness # 119250KIT. The ZCI kit is excellent for your 2023 Tesla Model 3 because you aren't getting into the vehicle wiring and cutting it up - just putting clamps over it. If you're planning on installing the EcoHitch Stealth Trailer Hitch Receiver # EH84GR then I also recommend picking up the following so you have a clean-looking setup: - Undercover Access...
  view full answer...
• What does the EcoHitch Trailer Hitch item # EH36SR Weigh?
  The EcoHitch Stealth Trailer Hitch item # EH36SR weighs 44 lbs. This hitch is confirmed to fit a 2022 Tesla Model S. I recommend using the Undercover Access Hole Cover for EcoHitch Stealth Trailer Hitch item # 306-XA2002. This will cover the hole the receiver extends through when you don't have the receiver installed.
  view full answer...
• Installing EcoHitch Stealth Receiver # 306-X7373 on 2020 Tesla Model 3
  I see exactly what you are referring to with regards to the plates that need to be removed on the 2020 Tesla Model 3 when installing the EcoHitch # 306-X7373. There is no need to worry though about rust or corrosion in that area because the mounting brackets for the hitch will essentially be taking their place. Using the included nylon washers and bolts the hitch brackets will create a tight seal at that location to prevent anything from creeping in between them and the frame. Once the...
  view full answer...
• Does Installing EcoHitch Trailer Hitch on 2022 Tesla Model 3 Void Any Warranty
  That is a good question, but no warranty on your 2022 Tesla Model 3 will be voided by installing the EcoHitch that fits your vehicle, which is the following part number: - EcoHitch Stealth Trailer Hitch Receiver # EH84GR The reason for that is you are protected by what is called the Federal Magnusson-Moss Warranty Act, which says if something breaks on your vehicle and you take it in for warranty repair, the dealer must honor your warranty unless whatever you have added to your vehicle...
  view full answer...
• Best Way to Carry a Bike Rack on a 2020 Tesla Model 3
  A trailer hitch, the EcoHitch Stealth Trailer Hitch Receiver # EH84GR, is definitely the best way to carry a bike rack on your 2020 Tesla Model 3 because it is going to be the sturdiest, most secure way to carry any type of bike a rack can handle. The EcoHitch Stealth has a 2 inch receiver which is completely removable so if you want to make it look like you don't even have a hitch on when you aren't carrying your bike rack, you can just remove the receiver and pop on the Undercover Access...
  view full answer...
  
• Best Trailer Hitch for Bike Rack on a 2019 Tesla Model 3
  The best trailer hitch for a 2019 Tesla Model 3 is the EcoHitch Stealth Trailer Hitch Receiver part # EH84GR. The EcoHitch installs completely behind the rear bumper so you will not even be able to tell a trailer hitch is even installed while the receiver tube is removed. This actually brings me to the removable receiver tube which is a feature specific to the EcoHitch and allows for a 100% factory like appearance. Please note, you will need to remove the rear bumper for installation but...
  view full answer...
  
• Installing EcoHitch Stealth Receiver on 2020 Tesla Model 3 and Concerns with Vehicle Rust
  That is a great question. Installing the EcoHitch Stealth Trailer Hitch Receiver # EH84GR does indeed require that a 3-1/2" or 4" oval be cut on the underbody trim to allow clearance for the 2" drop-down receiver on 2018 models and older. The 2019 models and newer have a cut out already so no trimming is necessary. Since the drop-down receiver can actually be removed when you aren't towing, I definitely see your concern about this opening a door for the elements to creep in and potentially...
  view full answer...
• What is Weight of EcoHitch for 2018 Tesla Model 3 and Access Hole Cover to Preserver Aerodynamics
  The weight of the EcoHitch part # EH84GR which fits your 2018 Tesla Model 3 is 45 lbs. When not in use you could use the access hole cover part # 306-XA2002 which would totally cover up the hole and would give you same aerodynamics as before the hitch was installed.
  view full answer...
  
• Will Undercover Access Hole Cover for EcoHitch Fit Stealth Hitch on 2018 Tesla Model 3
  The Undercover Access Hole Cover for EcoHitch Stealth Trailer Hitch Receiver # 306-XA2002 will fit the # EH84GR for your 2018 Tesla but it will not fit the # 391TES317. The EcoHitch cover is able to fit up inside of the tube for the removable receiver on the EcoHitch Stealth. The Stealth Hitch only has the small round hole for the removable receiver which would not be enough to allow the magnet and arm to fit and keep it secure.
  view full answer...
• Required Fascia Cutting When Installing EcoHitch Trailer Hitch on 2019 Tesla Model 3
  The installation instructions for the EcoHitch Stealth Trailer Hitch Receiver # EH84GR call for either a 3-1/2 inch or 4 inch hole saw. The advantage for the larger 4 inch hole is just more hand clearance to allow for easier mounting when inserting the receiver. I honestly just recommend going with the smallest possible hole (3-1/2 inches) as I'm sure you aren't overly enthused to cut into your Tesla's bumper fascia. HOWEVER, we have found that cutting is only needed on models before 2019....
  view full answer...
• Best Hidden Trailer Hitch For 2022 Tesla Model 3 For Bike Rack
  The best option for a hidden trailer hitch receiver for your 2022 Tesla Model 3 is from EcoHitch, with the correct part number for your '22 Model 3 being the following: - EcoHitch Stealth Trailer Hitch Receiver # EH84GR The Stealth has a completely hidden crosstube, and not only that, you can actually remove the receiver entirely when you aren't using it, so there is no trace of a hitch at all on your '22 Model 3. It is also one of just two hitches for your Model 3 with a 2" receiver,...
  view full answer...
• 2021 Tesla Model 3 Concerns with Corrosion After Install of EcoHitch Stealth Receiver
  Yes, this has come up several times as it is a valid concern because installing the EcoHitch Stealth Trailer Hitch Receiver # 306-X7373 does indeed require cutting. There is a 3-1/2" or 4" oval cut on the underbody trim to allow clearance for the removable 2" drop-down receiver and this opening to the elements causes concerns. But there is the availability of the Undercover Access Hole Cover # 306-XA2002. This is specifically designed to slide into the hitch when the receiver is removed...
  view full answer...
  
• Can Hole in Bumper Fascia from Installing EcoHitch Be Covered on 2021 Tesla Model 3
  The EcoHitch # EH84GR is indeed a fit for the 2021 Tesla Model 3, it'll work great for you. When the removable receiver is detached, the hole in the underside of the bumper fascia can indeed be covered using part # 306-XA2002. I've provided a photo showing the # 306-XA2002 cover installed. I've linked to install videos for both the hitch and the # 306-XA2002 cover.
  view full answer...

Do you have a question about this Accessories and Part?