Cover For Hitch Access Hole In 2020 Tesla Model 3 Fascia.

Question

Question:

Can I get A cover for the hole cut in the fascia on my tesla M3 to make room for a hitch?

asked by: Howard S

0

Expert Reply:

The Undercover Access Hole Cover for EcoHitch Stealth Trailer Hitch Receiver # 306-XA2002 will be able to cover the access hole for your stealth hitch on your 2020 Tesla Model 3.

I have linked some videos to help you see the product.

expert reply by: David B

0

Answer 1

You will need a 1-1/2" wrench like part #C20001 in order to install the nut on the 2" Hitch Ball part #63845. A 1-7/8" wrench would be much too large.

view full answer...

Answer 2

Curt recommends the use of 250 ft/lbs of torque when tightening the nuts of their hitch balls with a 1 inch diameter shank like the part #C40034 that you referenced. The general rule is for a 3/4" shank tighten to 150 ft/lbs For a 1" shank…

view full answer...

Answer 3

I would not think in Spain or France that they would use foot pounds since it isn't a metric measurement. But regardless I checked with Curt and the 450 foot pounds is what you would need.

view full answer...

Answer 4

Curt hitch ball #40038 has a 1 inch diameter shank. For Curt balls with 3/4 or 1 inch diameter shanks you would use wrench #C20001. The nut on that ball should use the 1-1/2 inch end of the wrench. You could also use a large crescent wrench if you…

view full answer...

Answer 5

We don't have a combo of the Curt Hitch Ball #C40008 and Curt Ball Mount #C45340. The ball mount is extremely heavy-duty, rated up to 17,000 pounds. I think it's safe to assume you don't have a torque wrench rated up to 450 foot pounds…

view full answer...

Answer 6

The installation instructions for the EcoHitch Stealth Trailer Hitch Receiver #EH84GR call for either a 3-1/2 inch or 4 inch hole saw. The advantage for the larger 4 inch hole is just more hand clearance to allow for easier mounting when inserting…

view full answer...

Answer 7

The dimensions of the Undercover Access Hole Cover for EcoHitch Stealth Trailer Hitch Receiver # 306-XA2002 that you referenced is 8-1/2" long by 5-1/16" wide by 1/8" thick. Your hole being initially cut with a 4 inch hole saw would…

view full answer...

Answer 8

The access hole cover, part #306-XA2002, isn't needed for all of the 2019 Tesla Model 3 so look under your car before getting it. Some of the 2019 models have a cover installed right from the factory.

view full answer...

Answer 9

It sounds like you are looking for the Undercover Access Hole Cover for EcoHitch Stealth Trailer Hitch item #306-XA2002. I have attached a picture below so you can confirm that this is the part you need.

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...