Dimensions of Undercover Access Hole Cover for EcoHitch Stealth Trailer Hitch

Question

Question:

Do you have exact dimensions of the cover? I made the access hole in my air dam using the 4inch hole saw as Torklift suggested for easier access, and want to know if this cover will still work. The default option for the access hole is using a 3-1/2inch hole saw, but I didnt have that size.

asked by: Dario V

0

Expert Reply:

The dimensions of the Undercover Access Hole Cover for EcoHitch Stealth Trailer Hitch Receiver # 306-XA2002 that you referenced is 8-1/2" long by 5-1/16" wide by 1/8" thick. Your hole being initially cut with a 4 inch hole saw would not be too large to work with this.

expert reply by: Jameson C

0

click to enlarge

Answer 1

The EcoHitch #EH84GR is indeed a fit for the 2021 Tesla Model 3, it'll work great for you. When the removable receiver is detached, the hole in the underside of the bumper fascia can indeed be covered using part #306-XA2002. I've provided a…

view full answer...

Answer 2

When installing the EcoHitch Trailer Hitch Receiver #EH84GR on 2018 Tesla Model 3's they needed to cut a 3-1/2" or 4" oval l(the larger opening will just give you more clearance to work with) on the underbody trim to make room for the…

view full answer...

Answer 3

The access hole cover, part #306-XA2002, isn't needed for all of the 2019 Tesla Model 3 so look under your car before getting it. Some of the 2019 models have a cover installed right from the factory.

view full answer...

Answer 4

It sounds like you are looking for the Undercover Access Hole Cover for EcoHitch Stealth Trailer Hitch item #306-XA2002. I have attached a picture below so you can confirm that this is the part you need.

view full answer...

Answer 5

You will need a 1-1/2" wrench like part #C20001 in order to install the nut on the 2" Hitch Ball part #63845. A 1-7/8" wrench would be much too large.

view full answer...

Answer 6

I would not think in Spain or France that they would use foot pounds since it isn't a metric measurement. But regardless I checked with Curt and the 450 foot pounds is what you would need.

view full answer...

Answer 7

We don't have a combo of the Curt Hitch Ball #C40008 and Curt Ball Mount #C45340. The ball mount is extremely heavy-duty, rated up to 17,000 pounds. I think it's safe to assume you don't have a torque wrench rated up to 450 foot pounds…

view full answer...

Answer 8

Curt hitch ball #40038 has a 1 inch diameter shank. For Curt balls with 3/4 or 1 inch diameter shanks you would use wrench #C20001. The nut on that ball should use the 1-1/2 inch end of the wrench. You could also use a large crescent wrench if you…

view full answer...

Answer 9

The Undercover Access Hole Cover for EcoHitch Stealth Trailer Hitch Receiver #306-XA2002 will be able to cover the access hole for your stealth hitch on your 2020 Tesla Model 3. I have linked some videos to help you see the product.

view full answer...

Answer 10

Curt recommends the use of 250 ft/lbs of torque when tightening the nuts of their hitch balls with a 1 inch diameter shank like the part #C40034 that you referenced. The general rule is for a 3/4" shank tighten to 150 ft/lbs For a 1" shank…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...